Thermal deformation temperature and liner expansion coefficient of the composite were decreased.
该复合材料的热变形温度有所降低，但线膨胀系数减小。
The resin toughness, the casting of the thermal deformation temperature is a good Comprehensive Performance winding resin.
该树脂韧性好，其浇铸体的热变形温度高是一种综合性能良好的缠绕用树脂。
The resin toughness, the casting of the thermal deformation temperature is a good comprehensive performance winding resin.
该树脂韧性好，是一种综合性能良好的缠绕用树脂。
Based on the resin curing the hardness and thermal deformation temperature higher, but also has a good climate of tolerance and toughness.
其基础树脂固化后的硬度和热变形温度较高，同时又具有良好韧性和耐气候性。
The resin produced by the flame-retardant products with high strength and mechanical properties, thermal deformation temperature, curing speed, and good soak.
该树脂所生产制品具有很高的阻燃性能和机械强度，热变形温度高，固化速度快，浸透性好。
The results show that thermal compensation in non-irradiant areas could reduce the temperature gradient of mirror for high-power laser, and then could decrease the thermal deformation significantly.
结果表明有效的热补偿对镜面变形峰谷值有很大的影响，在非光照区进行热补偿可以大大降低镜体的温度梯度，从而明显减小镜面变形的峰谷值。
This paper analyzed the difference between the temperature filed and thermal deformation in dynamic characters for spindle components.
文章对机床主轴组件温度场和热变形动态特性之间的差异进行了分析。
The temperature field and thermal deformation of the piston and ring carrier was used as the boundary in the calculation of stress field.
计算时把温度场和热变形作为结构应力计算的边界，获取活塞镶圈在热负荷状态下的综合应力场。
The difficulties of calculation are to establish the temperature field of structure under the action of ambient temperature and to calculate the thermal stress and thermal deformation.
其计算难点是建筑结构在环境温度作用下的温度场的建立与对应的温度应力和温度变形的计算。
The model for calculating the temperature distribution of leadscrew caused by grinding heat is established and the relationship between the temperature and thermal deformation is given.
建立了丝杠磨削热引起的温度分布理论计算模型，在此基础上分析了温升与工件热变形的关系。
The conventional calculation of thermal deformation of precision mechanism involves an exclusive consideration of the influence of temperature distribution on part deformation.
精密机械热变形计算中，通常只考虑温度在零件中的分布状况对零件变形所产生的影响。
The equations of thermal deformation of hollow piece under stress in uneven steady-state and even steady-state temperature field have been obtained.
采用热力学方法推导出稳态非均匀温度场中孔型零件在受力情况下的热变形公式。
The methods to reduce the machine tool thermal deformation are: thermal error modeling and compensation, temperature control, optimization design of thermal state characteristics.
减少机床热变形的方法为：进行热误差建模和补偿，温度控制，热态特性优化设计。
Then, the temperature field is loaded in FEA software to predict thermal stress and deformation.
并以此温度场为边界条件，利用FEA软件计算了机体热应力和热变形。
Based on the particularity of roll casting process, a practicable scheme is given for conveniently surveying the temperature field and thermal deformation of casting roller.
针对铸轧工艺的特殊性，拟定了一套方便可行的铸轧辊温度场及热变形测试方案。
This paper discusses the kinds of thermal load and regularities of temperature distribution in reinforced concrete frame structure, analyzes the cause of thermal deformation and thermal stress.
本文讨论了钢筋混凝土框架结构的温度荷载类型和温度分布规律，分析了钢筋混凝土框架结构温度变形和温度应力产生的原因。
The influence of the channel parameters of the water-cooled Si mirror on temperature and thermal deformation was simulated using ANSYS finite element analysis.
采用ANSYS有限元软件详细地研究了强激光作用下水冷硅镜的沟槽结构对镜面温升和变形峰谷值的影响。
Due to the atmosphere temperature change, the bridge superstructures' thermal deformation exist impersonality which is a fact.
由于周围大气温度的变化，桥梁上部结构产生的温度变形是一个客观存在的事实。
The transformation process to turn the thermal deformation caused by temperature factor into the mechanical model is discussed.
对由温度因素引起的热变形转换为力学模型进行了论证。
The thermal deformation caused by the change of temperature is widespread and inevitable.
温度变化引起的热变形是普遍存在并且不可避免的。
The difference between the temperature filed and thermal deformation in dynamic characters for spindle components is analyzed.
对机床主轴组件温度场和热变形动态特性之间的差异进行了分析。
Mechanism of damage of clay pot for utensil glass melting, such as softening deformation at high temperature, corrosion by molten glass, crack by thermal shock, etc was studied.
对熔化器皿玻璃等的粘土质坩埚使用中的高温软化变形、玻璃液侵蚀、热震开裂等损毁机制进行了分析研究。
Use of the finite element method, the thermal environment of space under the support of the inflatable antenna and the temperature distribution and thermal deformation.
利用有限元方法，分析了空间热环境下的支撑管和充气天线的温度场分布和热变形问题。
The deformation and displacement of magnet and thermal shield will take place due to the temperature change during EAST operating.
EAST运行中的温度改变会导致磁体及冷屏产生形变和位移。
The principle of thermal analysis method and the procedure were introduced in detail. At the same time, the deformation temperature of pipe line X80 steel and Q235 steel were determined.
详细介绍了热分析法的原理及其具体的实现方法，同时对X80管线钢与Q235钢进行了试验，测量了其冷却过程的相变点。
Based on the finite element theory of non-linear thermal coupling, coupledly analyse the interaction between temperature load and the deformation.
体现了铝板坯铸轧过程为材料非线性、几何非线性和接触非线性的大变形。
Based on the finite element theory of non-linear thermal coupling, coupledly analyse the interaction between temperature load and the deformation.
体现了铝板坯铸轧过程为材料非线性、几何非线性和接触非线性的大变形。
应用推荐