It is of great importance to rhythm and coordination of the thin slab continuous casting and rolling process.
时间因素对薄板坯连铸-连轧流程的节律性、协同性而言，其意义尤为重要。
This system can solve the dynamic schedule problem of two-strand thin slab casting and rolling and optimize production management.
该调度系统可以较好地解决两流薄板坯连铸连轧流程的动态调度问题，进一步优化生产组织。
Schedule rules for two-strand thin slab casting and rolling were established.
首先建立了两流薄板坯连铸连轧流程生产调度规则库。
The status of thin strip production in thin slab casting and rolling process at Zhujiang steel is introduced, and main factors which affected the production is analyzed.
介绍了珠钢薄板坯连铸连轧生产线薄规格的生产情况，分析了影响薄规格生产的主要因素。
The cleanliness of molten steel is a key factor for thin slab casting.
洁净钢的生产是薄板坯连铸的关键问题。
The causes of surface longitudinal cracking were analyzed. Countermeasures were put forward based on the production practices of thin slab casting and rolling at Tonghua Steel Co.
分析了连铸薄板坯表面纵向裂纹的产生原因，结合通钢薄板坯生产实际情况，提出了改进措施。
Based on the simulation, some typical processes were investigated, and some useful Suggestions for the design of thin slab continuous casting and rolling line were proposed.
采用该软件对个别典型的工艺进行分析，为连铸连轧生产线的设计提出了有益的建议。
This program was applied to calculate the temperature distribution of copper thin-slab continuous casting with different casting speeds and cooling conditions.
利用该程序计算了不同拉速及冷却条件下，铜薄板连铸过程中温度场的分布，并分析了拉速、冷却条件对铸坯温度的影响。
Macroscopic fluid flow and heat and mass transfer should be taken into account for the continuous thin slab casting process.
薄板坯连铸工艺应综合考虑传热、流动与传质宏观传输现象。
It showed that EMBR could control vortex and improve the flow field in the thin slab continuous casting mould effetely.
计算表明，电磁制动对于抑制涡旋、改善薄板坯连铸结晶器中的流场有明显效果。
In the project of ASP1700 thin slab continuous casting and rolling, the system of mould width adjust in the continuous casting is equipped with the new digital alternating servo control system.
在济钢ASP1700薄板坯连铸连轧项目中，连铸机结晶器调宽系统采用了新型全数字交流伺服控制系统，代表当今世界最先进控制水平。
Buffer time of tunnel furnace is the key process in thin slab continuous casting and rolling (TSCR) line.
在薄板坯连铸连轧生产线中，加热炉的缓冲能力有时成为制约生产的关键。
Rather new manufacturing technologies such as thin slab casting rolling and twin roll casting technology were prospected.
介绍了具有代表性的研发趋势，如薄板坯连铸连轧、双辊薄带铸轧等新工艺。
The slab quality was the key to the research of thin slab continuous casting and rolling process.
铸坯质量问题是薄板坯连铸连轧工艺研究的核心问题。
This paper describes the characteristics of medium and thin slab continuous caster in detail and the principles must be observed to fit these characteristics during designing the casting powder.
详述了中薄板坯连铸机的特征，以及保护渣设计过程中，为适应这些特征所必须遵守的原则。
Thin slab concast & conroll combines the near net shape continuous casting and the direct rolling together, thus to shorten the conventional continuous casting & rolling process.
薄板坯连铸连轧将近终形连铸与直接轧制相结合，缩短了传统连铸与轧钢工艺流程。
Results from the analysis provides basis for the system optimization of the thin slab casting and rolling process.
分析结果为薄板坯连铸连轧流程的优化提供了依据。
In this paper, mathematical model and FEM software for the simulation of thermal process during continuous casting and rolling of thin slab were developed.
本文针对连铸连轧的热过程，建立了各工艺的热过程的数学模型，并开发了相应的软件。
Electromagnetic braking on flow field of molten steel in the thin-slab continuous casting mold is analyzed by mathematical modeling and experiment.
采用模型实验结合数值模拟的方法分析了薄板坯连铸结晶器的电磁制动过程。
Combining the advantages of conventional and thin-slab-production routes, this casting process is highly flexible and well suited for casting slabs used for a wide range of applications.
通过结合传统板坯连铸和薄板坯连铸的优点，中厚板坯连铸技术具有高度的灵活性，完全适合浇铸用途广泛的板坯。
The vortex flow and mold flux entrapment in the thin slab continuous casting mold was investigated using a 1/4 scale water model.
利用1/4水模型对薄板坯连铸结晶器内的涡流及卷渣行为进行观察研究。
It will also foster the further perfection of EAF technology and the ubiquitous use of Thin Slab Casting.
回收再利用也将推动电弧炉技术的进一步完善和薄板坯连铸技术的广泛采用。
The thin slab continuous casting technique had been adopted in metallurgical production to gain the remarkable benefits.
薄板坯连铸技术已应用于冶金生产并取得显著效益。
The process of thin slab continuous casting and direct rolling is different from the traditional one.
薄板坯连铸连轧工艺的生产流程有别于传统工艺流程。
A suggestible solution is the combined production of thin slab continuous casting and continuous rolling together with strip casting, so that it will be complemental in superiority for both of them.
利用薄板坯连铸连轧和薄带铸轧组合方案生产不锈钢可以更好地形成优势互补。
Using incompressible MHD equations and zero equation turbulent model, the paper calculated the flow field in two dimension thin slab continuous casting mould with the electromagnetic brake(EMBR).
本文采用不可压缩MHD方程及零方程湍流模式，数值计算了加电磁制动器的二维薄板坯连铸结晶器中的流场。
The production and technical situation of thin slab continuous casting with FTSC process in Tang Steel are introduced briefly.
简要介绍了唐钢FTSC工艺薄板坯连铸的生产技术情况。
It shows that thin slab continuous casting has a greater secondary cooling intensity, a faster solidifying rate, a fine and uniform structure and less segregation than conventional slab casting.
研究表明，薄板坯的二冷强度大，凝固速度快，组织细小、均匀，其内部溶质元素的偏析程度远低于传统连铸板坯。
Research and development of mould powder for low carbon steel thin slab casting specially used in cold rolling at TISCO is introduced.
介绍了唐钢薄板坯连铸低碳冷轧用钢保护渣的研究开发过程。
This paper describes the production condition of cold rolled deep drawing quality steel (IF steel) by thin slab continuous casting and rolling technique in Bengang.
介绍了本钢薄板坯连铸连轧工艺生产冷轧深冲钢(IF钢)的情况。
应用推荐