XE--- Rack shift coefficient for adjustment of tooth thickness.
按照字面是：调节齿厚的齿条位移系数。
The accuracy of the model are analyzed as transverse tooth thickness is research object.
并以齿厚为分析对象，对模型的精确性进行了讨论。
The selections differ only in the tolerance as applied to space width and tooth thickness.
选择不同的公差在“弧齿槽宽”和“弧齿厚”中应用。
Gear tooth thickness at the site are unilateral wear, so gear can be rotated 180 degrees to use.
齿轮在齿厚部位都是单侧磨损，所以可将齿轮翻转180度使用。
Machining Tolerance is the permissible variation in actual space width or actual tooth thickness.
加工公差是花键的实际齿槽宽和实际齿厚的允许的变动量。
And finally a new norm is put forward for selecting backlash and tooth thickness deviation of gears.
最后，提出了一种新的侧隙和齿厚偏差选择规范。
Machining Tolerance (m) is the permissible variation in actual space width or actual tooth thickness.
加工公差(m)：加工公差是花键的实际齿槽宽和实际齿厚的答应的变动量。
There is only approximate way to work out the normal chordal tooth thickness of worm and wormwheel at present.
目前所见到的圆柱蜗杆蜗轮分度圆弦齿厚计算公式均为近似公式。
Deviation measurement of tooth thickness and conical point of straight bevel gear by using steel bail was studied and approached.
对钢球法测量直齿圆锥齿轮齿厚及锥项位置误差检测进行了研究和探讨。
Formulas are given in many mechanical manuals to calculate the tooth thickness at only the reference circle of worm and worm wheel.
蜗轮蜗杆的分度圆齿厚在大部分机械手册中都给出了计算公式，但在其它任意半径处的齿厚计算很少有资料涉及。
This article mainly introduces the method that adopts gear caliper to measure the median diameter normal tooth thickness of double-line trapezoidal thread.
本文主要介绍了采用齿轮卡尺测量双线梯形螺纹中径法向齿厚的方法，同时也测量出螺距产生的误差。
There is no common normal in the conical involute gear and the fixed chordal tooth thickness can not be measured accurately because of the coexistence of helix angle and taper.
渐开线锥形齿轮由于同时存在锥度和螺旋角，使得其固定弦齿厚无法精确测量，也没有公法线。
Firstly, according to the analysis of the forming principle of the involutes profile and the tooth thickness of formula, a mathematical model of involutes profile was established.
首先，根据对渐开线齿廓形成原理和渐开线齿轮任意圆上的齿厚公式的分析，建立了插齿刀的渐开线圆柱齿轮齿廓的数学模型。
Because of the tooth thickness of the dedendum is larger than that of the common involute gear and the Pitchs do not contact each other, the beam strength and surface strength of tooth are increased.
由于该齿轮的齿根厚度比普通渐开线齿轮的齿根厚，并且节点附近不相接触，因此，其轮齿弯曲强度和接触强度都提高。
Thickness of the tooth body; Root canal therapy; Research.
牙体壁厚度；根管疗法；研究。
The distribution of engaging efficiency, EHD oil film thickness and tooth face wear and their changes along with transmission parameters are presented.
给出了超环面行星蜗杆传动啮合效率、齿面磨损量和弹流油膜厚度的分布规律及其随传动参数的变化规律。
AIM: to study the stress distribution of periodontal membrane of fixed abutment tooth with different thickness, and provide theoretical basis in clinic.
目的：研究固定桥基牙牙周膜厚度不同时牙周膜内的应力分布，为临床工作提供理论依据。
The film thickness is analyzed with elastohydrodynamic lubrication theory, tooth elastic deformation computed by finite elements.
并利用弹流理论来研究啮合轮齿间油膜厚度，用有限元法来研究轮齿受载弹性变形。
Conclusion: the thickness of buccal bone wall and position of missing tooth, may influence the maxillary alveolar ridge alterations after immediate implantation.
结论：颊侧骨板的厚度及缺牙位置均有可能影响术后牙槽嵴的改建。
The dental floss has advantages that: the diaphragm has small thickness and is convenient to enter into tooth clearance;
本实用新型所述牙线的优点在于，膜 片厚度小，可以很方便地进入牙齿间隙；
The ratio of rim thickness to tooth height was defined for representing the flexibility of internal ring gear.
以轮缘厚度系数来描述内齿圈的柔性，以均布的弹簧约束来反映内齿圈与机体的配合情况。
Clean substrate, apply the mortar on substrate, rub the mortar strip-shaped with a side-tooth trowel, and then can stick ceramic tiles. the thickness is about 2-3mm.
基层处理干净后，将砂浆涂抹于基面，再用侧面带齿抹子将砂浆揉成条沟状后，即可粘贴饰面瓷砖，粘贴厚度为2 - 3 mm。
The Tooth Length, Crown Length, Root Length, Cervix Width, Cervix Thickness, Crown Width and Crown Thickness were measured with a vernier caliper.
用游标卡尺分别测量牙长、冠长、根长、颈宽、颈厚、冠宽和冠厚；
The Tooth Length, Crown Length, Root Length, Cervix Width, Cervix Thickness, Crown Width and Crown Thickness were measured with a vernier caliper.
用游标卡尺分别测量牙长、冠长、根长、颈宽、颈厚、冠宽和冠厚；
应用推荐