The stress shielding rate, bending strength of different directions and torsion strength of the three different fixation methods were measured and compared.
然后对三种固定方法对固定骨段的应力遮挡率、不同加载方向的弯曲强度和扭转强度进行测试。
Since there are many special structural characteristics of ro-ro vessel different from general ships, it is necessary to calculate the bending and torsion strength of the ro-ro vessel accurately.
由于滚装船有着不同于常规船舶的结构特点，有必要对其进行全船弯扭强度精确计算。
The Speedy Rail beam is a heat-treated aluminium alloy profile with hollow cross-sections that give it high strength under torsion and deflection stresses.
快速铁路是束热处理铝合金型材中空截面，给高强度下的扭转和挠度应力。
Due to the effect of strain hardening, higher amount of cold deformation resulted in superior room temperature strength and inferior torsion ductility.
由于加工硬化效应的影响，随着冷拔变形量的增加，合金丝材的室温强度增加，扭转塑性下降。
Torsion moment coefficient is the key parameter for torsion moment-method construction of high strength bolts.
扭矩系数是高强度螺栓扭矩法施工的关键参数。
The purline is often designed as a simple beam, and only it′s strength needs to be calculated, if the roof panel can prevent it′s lateral buckling and torsion.
檩条一般采用简支梁，假定屋面板能阻止其侧向失稳和扭转，则只计算其强度。
The effects of secondary torsion on shear strength of biaxial flexural reinforced concrete beams are analyzed.
探讨了次生扭矩对钢筋混凝土双向受弯梁抗剪承载力的影响。
In this paper all experimental results of the torsion moment coefficients of high strength bolts with two kinds diameters, M27 and M24, and different plate combinations are presented.
本文介绍了M 27和M24两种直径高强度螺栓不同板束组成时扭矩系数的全部试验结果，可供实际使用时参考。
Then the article conducts static analysis of the body frame under bending and torsion condition, so that preliminary to assess the risk static strength location of the body structure.
然后分别对车身骨架进行了弯曲和扭转工况下静态分析，初步评估车身结构静强度危险位置。
Automotive half shaft flange is a coupling part under the combined action of bending and torsion, its strength, loading and actual size have an uncertainty.
汽车半轴凸缘是受弯扭联合作用的联接零件，其强度、载荷及实际尺寸具有不确定性。
Based on the experimental results, this paper studies the strength and deformation of reinforced high strength haydite aggregate concrete member in torsion and bending.
在试验的基础上对钢筋高强陶拉砼构件在纯扭和弯扭作用下的受力和变形性能进行了研究。
Steel Series: steel with high strength large hexagon head bolts, torsion shear bolt connections made, the steel truss joints of high strength bolts, studs, drill the end of wire.
钢结构系列：钢结构用高强度大六角头螺栓，扭剪型螺栓连接副，钢网架球节点用高强度螺栓，焊钉，钻尾丝等。
Results:There were significant difference in the strength to resist bending, extending, lateral bending, axial torsion and axial displacement of the fusion unit between the two groups.
结果：复合骨环组在抗屈曲、抗伸展、抗侧弯和抗纵向位移方面与自体髂骨块组间存在显著性差异。
It was indicated that distributing the strength according to design eccentricity could reduce the inelastic torsion of asymmetric structures.
分析结果表明：通过设计偏心距对偏心结构进行强度分配，可以控制弹塑性扭转反应并提高结构侧向变形能力。
The experiment done by the authors shows that the RC torsion members strengthened by CFRP straps have significant strength gain.
试验研究表明，用CFRP条带加固钢筋混凝土受扭构件，对构件承载能力的提高有非常显著的作用。
Experimental results of 16 reinforced steel fiber high strength concrete members with rectangular cross section under pure torsion are reported.
对16根矩形截面配筋钢纤维高强混凝土纯扭构件进行了试验研究。
Its advantages are low torsion resistance and drive noise, improved dynamic balance, high compression strength and long service life.
减低传动噪音，动平衡性能改善，滑动节使用寿命提高；提高涂层抗压强度。
The behavior of steel fiber high-strength concrete rectangular members subjected to pure torsion is studied.
通过钢纤维高强砼矩形截面构件的受扭试验，着重探讨了钢纤维对纯扭构件抗扭性能的影响。
To determine the anti-slip coefficient of the high-strength bolt which connects components of friction surface, it is screwed and determined by torsion and tensile testing machines respectively.
大六角头高强度螺栓连接副扭矩系数的检测，扭剪型高强度螺栓连接副坚固预拉力的检测，高强度螺栓连接磨擦面抗滑移系数的检测，是钢结构材料验收中的重要测量。
To determine the anti-slip coefficient of the high-strength bolt which connects components of friction surface, it is screwed and determined by torsion and tensile testing machines respectively.
大六角头高强度螺栓连接副扭矩系数的检测，扭剪型高强度螺栓连接副坚固预拉力的检测，高强度螺栓连接磨擦面抗滑移系数的检测，是钢结构材料验收中的重要测量。
应用推荐