Can this armor plate be exchanged to welding line?
这列钢板换到焊缝处好吗？
Introduced planar welding line detect sensor based on GMR.
简述了基于GMR的二维焊缝检测传感器。
A three-dimensional welding line detect sensor based on GMR was introduced.
简述了基于GMR的三维焊缝检测传感器。
This welding line should be gouged and welded again before tightness inspection.
这条焊缝在密性检查前要碳刨、再焊。
Applicable to special material repair or cold stamping mould buttering welding line.
适用于特殊材料的修补堆焊或者冷冲压模具的衬焊使用。
Specially suitable for zinc patching of weld seam in tube welding line, and capacitor spray.
本套设备尤其适合于高频焊管生产线上进行焊缝的补锌及电容喷涂。
The general problem of half-pipe jacket is the leakage of the welding line induced by crack.
半圆管夹套设备最常见的问题是夹套焊接部位开裂引起泄漏。
The space between the welding line was optimized by NX NASTRAN, through which an ideal space was obtained.
对客车局部的焊缝间距进行了优化，得出了较理想的焊缝间距。
And basic design technique of pneumatic system of Automotive welding line is discussed combined with the practice.
结合实践，探讨了汽车焊装线气动系统的基本设计技术。
In this paper, a new design of tangent bridge structure was proposed, which can reduce or even avoid welding line.
本文对圆管型材制品，给出了一种切线分流桥的结构，能够减轻甚至避免圆管表面出现明显焊合线；
Study on the properties of welding line near line section aluminium lithium alloy 1420 by Russia scholar is introduced.
主要介绍了俄罗斯学者关于铝锂合金1420焊缝近缝区性能的研究点滴。
When welding voltage is between 21v and 24v and welding current is between 210a and 270a, better welding line can be obtained.
发现超窄间隙焊的焊接电压范围在21 ~24v，电流在210 ~ 270a能够得到较好的焊缝成形。
The reasons that why the stainless steel welding line of 304 might be corroded in the production of formaldehyde were analyzed.
分析了甲醛生产中304不锈钢焊缝腐蚀的原因，并提出甲醛冷却器型式的选择。
In this system, the laser distant sensor is used to measure the vertical welding line and the PLC is used to control the system.
该系统利用PLC作为控制核心，采用激光测距传感器来检测垂直焊缝。
The paper describes the application of the ultrasonic in welding car's bumper, especially in the construction of the welding line.
本文介绍超声波在国产轿车后保险杠总成焊接中的应用，着重介绍了该焊装线的组成。
Tap the welding line, blind angle and the bottom when washing pipes of more than 100mm diameter and take care not to damage pipes.
的管道时，要对其焊缝、死角和底部进行敲打，但不得损伤管道。
In addition to causing the welding line to break off, may also lead to other local damage near the welding line, such as sealing data.
除了招致焊接线烧断外，还可能招致靠近焊接线的其他局部损坏，例如密封资料。
The probe choices for ultrasonic crack detection of welding line of light sheet are discussed from two aspects of theory and practice.
从理论和实践两方面探讨了薄板焊缝超声波探伤探头的选择方法。
The results indicated that the welding technique is simple, the performance of the welding line is excellent and the application is broad.
无电焊接技术焊接工艺简单，焊缝性能优良，应用广泛，具有良好的推广应用价值。
The microhardness distribution of the welded joint is along the welding line. The microhardness is higher in nugget zone, and lowest in HAZ.
焊接接头的硬度分布沿焊缝中心基本对称，焊核区硬度较高，热影响区硬度最低。
The failure form of Ji 'nan luminous character after being subjected to electric shock is not fixed, but it usually causes welding line damage.
济南发光字遭受过电冲击后的失效形式并非固定，但通常会招致焊接线损坏。
The microhardness declined from the welding line to base metal, and the microhardness of the welding line was about 35 higher than that of base metal.
从焊缝区到母材，显微硬度值逐渐下降，焊缝区硬度值高出母材约35。
A kind of automatic welding equipment with the tracking system for horizontal welding line in inverted construction of vertical storage tank is developed.
设计了一种立式储罐倒装施工用自动跟踪式横焊缝自动焊装置。
The distance break can be measured by the laser distance sensor when the welding line passing and the passing time can be calculated using the arithmetic.
当焊缝经过激光传感器前时，激光传感器会检测到距离突变，通过算法可判断出焊缝经过的时刻。
Welding clamp configuration design was the key step for the whole welding line reconfiguration and its keystone was orientation and part's standardization.
焊装夹具快速重构设计是汽车焊装生产重构实现的关键，其重点在于定位问题和元部件标准化。
The steel with discontinuous flowline microstructure has lower grooving corrosion susceptibility and only single corrosion groove exists along the welding line.
而不连续流线组织的钢板具有较低的沟槽腐蚀敏感性，在焊缝处产生单腐蚀沟槽。
The steel with discontinuous flowline microstructure has lower grooving corrosion susceptibility and only single corrosion groove exists along the welding line.
而不连续流线组织的钢板具有较低的沟槽腐蚀敏感性，在焊缝处产生单腐蚀沟槽。
应用推荐