Its resilience is strong during shaping, because titanium's ratio of yield limit to elasticity modulus is high.
由于钛的屈服极限与弹性模量的比值大，使钛成型时的回弹能力大。
Under the instantaneous strain and yield limit calculated, judgement rule about viscoelastic and viscoplastic is established.
通过计算瞬时应变的大小与屈服限建立粘弹性变形和粘塑性变形的判断准则。
The initial yield pressure of the cylinder is gained by analyzing the experimental data, and then the yield limit is calculated.
通过对该试验数据的分析得到了圆筒的初始屈服压力，最终求得了材料的屈服极限。
Though the peak value of the stress in part areas exceeds the yield limit of the cast steel, as the yielding areas are small an.
线弹性及非线性分析结果表明，最不利工况下，部分节点局部区域的峰值应力有超过铸钢屈服极限的情况，但屈服区域范围小，同时最大应变值尚小。
In two and three dimensions the yield limit is reached when a certain function of all the stress components reaches a fixed value.
在二维或三维的情况下，屈服极限是当所有应力分量的某个函数达到某一固定值时达到的。
The main reason of the main beam down deflection was that the most complex stress exceeded the admissible value and achieved the yield limit value.
主梁下挠变形的主要原因是受热引起的最大复合应力超过许用值，达到了屈服极限值，强度不满足要求。
The most dangerous point is at the root of the first engaged tooth of a joint. Generally, the biggest values of stress and strain may exceed the yield limit.
最危险点在接头的第一啮合齿的齿根处，最大应力应变值一般均超过屈服极限。
To make automobile panel rapidly and accurately, the yield limit, hardening modes and invalidation modes of materials for large automobile panels were analyzed.
为了快速、准确地制造汽车车身覆盖件，对大型汽车覆盖件材料的屈服极限、强化模式以及失效模式进行了分析。
Increasing the yield limit of high strength steel, and increasing the depth of submergence, the form of the differential equation's result will not only be limited with the complex number.
由于高强度钢材的屈服极限不断地增大，下潜深度的不断增加，弯曲微分方程解的形式将不仅限于复数解。
Some ideas on improvement in prestressing process are raised according to the observation and analysis on modulus of elasticity, apparent yield limit, tensional strength and percentage elongation.
根据对弹性模量、非比例强度、抗拉强度和断裂伸长率的观察分析，提出了预应力钢丝张拉施工工艺的改进意见。
So, please, decide now to deliberately limit the time and attention you spend on "low yield" relationships.
所以，请现在就有意识地限制对“低产”关系花的时间和注意力。
But it has clearly reached a limit in creditors' willingness to supply funding at a reasonable yield, and may have reached the limit of taxpayers' willingness to pay the eventual bill.
但这很明显已经直抵债权人与纳税人所能承受的上限了，债权人不愿意再以此利率提供资金了，纳税人也不愿意再为亏空买单，收拾残局了。
Fatigue strength is less than static stress strength such as elasticity limit, yield strength.
疲劳强度低于弹性极限或屈服强度等静应力强度。
Silicon can obviously improve the elastic limit, yield point and tensile strength of steel.
硅能显著进步钢的弹性极限，屈从点和抗拉强度，故普遍用于作弹簧钢。
The incipient yield pressure of the cylinder is gained by analyzing the experimental data, and then the limit of yielding is gained.
通过对该实验数据的分析得到了圆筒的初始屈服压力，最终求得了材料的屈服极限。
The aim is to obtain a high yield strength, elastic limit and high toughness.
其目的是获得高的屈服强度，弹性极限和较高的韧性。
These factors in the near future there will be no fundamental change, will limit the total assets of China's banking yield level.
上述因素在近期内不会有根本性的改变，仍将限制我国银行的总资产收益率水平。
Consequently, the limit damping force of the unequal model proves the peak damping force (yield shear force) of the equal model.
证明了非均匀模型的极限阻尼力是均匀模型的最大阻尼力(屈服剪力)。
Because the analyte molecules are recognized by forming the binding complex with antibody, a decrease in the detection limit is achieved only by an increase in the reaction yield.
因为分析物分子能通过与抗体形成结合物而被发现，所以降低检测极限只能通过增加反应产率来达到。
A proposed method is presented to design lead shear dampers according to the limit damping forces and yield displacements.
以极限阻尼力和屈服位移为参数，给出了阻尼器的设计方法。
The distingUishing featUres of the paper are the influences of line loads on models of yield line, the method of selecting strips, and the method of the limit analysis of the slab under line loads.
文章的主要特点为线荷载对屈服模式的影响，条带的选取方法，线荷载作用下板的极限分析方法。
The strain yield locus of the stress yield criterion was advanced and the strain ellipse method for calculating the limit bulging coefficient was given.
提出应力屈服条件的应变屈服轨迹，给出了复合胀形极限成形系数的解法；
Other he may maximum limit yield.
别的他可以最大限度让步。
The yield criterion of composite materials is simulated by using the homogenization method of micromechanics and the plastic limit analysis theory.
运用细观力学中的均匀化方法和塑性力学中的极限分析理论，分析了复合材料的屈服准则。
Soil salinity is one of chief environmental factors that limit the crop yield potential.
土壤盐渍化是降低农作物产量的主要环境因素之一。
It is the fine cementation of microcracks so as to reduce or eliminate the stress concentration on their ends intensively. Thus, the limit yield of rock mass and its strength are both enhanced.
微细裂隙的良好胶结，使其端部应力集中被降低或消除，岩体屈服极限增大，强度提高。
The wheat leaf is the main organ for photosynthesis. The decline of assimilation induced by leaf senescence may limit yield potential.
叶片是小麦进行光合作用的重要器官，其衰老引起的叶片同化功能减退限制了小麦产量潜力的发挥。
The characteristic line method meets the static equilibrium equations and yield conditions, which gives the lower limit of the solutions.
本方法满足静力平衡方程和屈服条件，属于极限分析理论的下限解。
In the plastic limit analysis, the wrinkler's plate is smartly analyzed in yield-line theory to get the critical compression strength of the coal pillar.
在分析过程中，利用机动法对温克尔地基板（弹簧支撑板）进行了塑性极限分析，得出了煤柱抗压强度的临界值。
In the plastic limit analysis, the wrinkler's plate is smartly analyzed in yield-line theory to get the critical compression strength of the coal pillar.
在分析过程中，利用机动法对温克尔地基板（弹簧支撑板）进行了塑性极限分析，得出了煤柱抗压强度的临界值。
应用推荐