Results show that the additional temperature stress and deformation of the continuously welded turnout will increase with the increase of rail temperature.
结果表明：无缝道岔的附加温度力与变形随轨温变化幅度的增大而增加；
The results show that after alternate deformation, with the increase of heat treatment temperature, the nucleation ratio of recrystallization rises.
结果表明，弯折压平交替变形后，随热处理温度的升高，再结晶形核率增加。
The test results suggest that the creep value in deformation becomes larger when the water content and temperature increase.
通过对试验结果进行分析后认为加筋膨胀土挡墙在含水量和温度升高时其蠕变变形会变大；
The results show that the flow stress and peak strain increase with increasing strain rate or decreasing deformation temperature.
结果表明：实验条件下，流变应力及峰值应变随变形温度的降低和应变速率的提高而增大。
With the increase of forging temperature, the deformation resistance and stress for working are decreased, which brings about the improvement of formability.
随着锻造温度的增加，变形抗力和加工应力减小，合金的成形性能得到提高。
The results of experiments show that tensile strength, bend strength, bend modulus and heat deformation temperature of the composite materials are increased with the increase of carbon fibre content.
随碳纤维比例的增大，该复合材料的拉伸强度、弯曲强度、弯曲模量及热变形温度均呈上升态势；而缺口冲击强度及击穿电压呈下降态势。
The results show that the increase of cyclic frequency would decrease high temperature fatigue lifetime of the alloy and result in different deformation mechanism.
结果表明，循环频率的增加会导致合金高温疲劳寿命的下降及不同的变形机制。
The size of dynamically recrystallized grain decreased with the increase of strain rate and increased with the increase of deformation temperature.
动态再结晶晶粒尺寸随应变速率的增加而减小，随变形温度的增大而增大。
The results show that the softening ratio increases with the increase of deformation temperature and interval time.
结果表明，其静态软化率随变形温度的升高和道次间隔时间的延长而不断增加。
The results show that the dislocation density decreases and the subgrain sizes increase with the increase of deformation temperature and the decrease of the strain rate;
结果表明：随着变形温度的升高和应变速率的减小，位错密度减小，亚晶粒尺寸增大；
The results show that the increase of stress range value would result in decreasing the high temperature fatigue lifetime of the alloy and the difference of the deformation mechanism.
结果表明，应力幅值的增加会导致合金高温疲劳寿命的下降及使变形机制改变。
When deformation temperature is constant, flow stress increases with the increase of strain rate.
当温度一定时，流变应力随着应变速率的升高而增大。
With the increase of deformation temperature, thick second phase reduces, the strength of T6 alloy increases, but plastic decreases first and then increases.
变形温度升高，合金中的粗大第二相减少，T6态铝合金强度随变形温度的升高而增大，塑性则先降低后增加。
Results show that the critical nucleus will be reduced and the initial transformation temperature of ferrite improved with increase of the deformation store energy.
计算表明，变形能的加入可以使临界核胚减小，并且提高铁素体开始转变的温度。
Wet samples have obvious buckling or plastic deformation, and the phenomenon more obvious with the increase of temperature.
湿态试样的后期会有明显的弯折或塑变，而且随着温度的升高这种现象越明显。
The results show that the flow stress and peak strain of 300M steel increase with the increase of strain rate or the decrease of deformation temperature.
流变应力和峰值应变随变形温度的升高和应变速率的降低而减小；
The deformation moves CCT curve to left and up direction. the cooling transformation initiating temperature of austenite increases more with the increase of cooling rate.
变形使CCT曲线向左上方移动，提高了奥氏体冷却转变开始温度，随冷速加大提高得越多。
Compared with both of them, the peak-value strength, elastic modulus, and deformation modulus of sandstone after high temperature increase by a little and they are all brittle fractures.
两者相比，高温后砂岩的峰值强度、弹性模量和变形模量有所提高，两者受温度影响均以脆性破坏为主。
The results show that the flow stress and peak strain increase with either increasing strain rate or decreasing deformation temperature.
试验结果表明，流变应力和峰值应变随变形温度的降低和应变速率的提高而增大。
The results show that the flow stress and peak strain increase with either increasing strain rate or decreasing deformation temperature.
试验结果表明，流变应力和峰值应变随变形温度的降低和应变速率的提高而增大。
应用推荐