The metal particles removed from the die block are washed away with the dielectric fluid which is circulated.
从模块上去除地金属屑被循环流动地电火花加工液冲走。
In addition, the die block used only with marketing materials and Crook block behind the marketing materials.
此外，本模具采用始用挡料销和钩形挡料销挡料。
The metal particles removed from the die block are washed away with the dielectric fluid, which is circulated.
从模块上去除的金属屑被循环流动的电火花加工液冲走。
The copper-made die block in which a conical welding opening is bored is arranged on the middle part of the upper die.
上模为中部开有锥形焊口的铜制模块，焊口位置与底模熔池对应。
With using CAM module of UG software to compile the machining program, owing to the reasonable process based on IPW, efficiency of the die block has been increased greatly.
利用UG软件CAM模块来编制加工程序，提出基于IPW的最佳数控加工工艺，提高模具模块加工的效率。
The vertically float die block and slide plate of combination movement have been adopted in the die to form a ring part on a single stroke of the press with high productivity.
该弯曲模采用浮动模块和复合运动的滑板，使环形零件在压力机一次行程中成形，工作效率高。
The main reason that causes early failure of glared tile die block is found through analysing. The analysing has some guiding functions for ingrowing using life of the glazed tile die block.
通过对釉面砖模板过早失效分析，从中找出引起失效的主要原因·对提高其使用寿命有一定的指导作用。
Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block.
在上模节流棒槽内装入节流棒，将节流棒调节螺栓装配进节流棒的螺丝孔中，再装配上压块。
The practical structure of a precision bending die with a turning block is presented.
介绍了翻转模块式精密弯曲模的实用结构及模具工作过程和结构特点。
The practical structure of a precision bending die with a turning block is presented. The working process and structure characteristics of the die are described.
介绍了翻转模块式精密弯曲模的实用结构及模具工作过程和结构特点。
If the casting is taken out from the moving die, long distance core pulling is needed according to the shape of the casting, so the mechanism of the sliding block which rotates midway was designed.
根据铸件形状特点，若在动模内取出铸件，需长距离抽芯，故设计了滑块中途自行转动机构。
The three block self plugging structure of rubber impeller die is introduced.
介绍了橡胶叶轮模具三块式抽芯结构。
Blind embossing: a general term FOR the process of raising an image using an un-inked block or die on paper or board.
素压浮凸：泛指用不着墨的电或模在纸品上压成凸纹效果的方法。
The structure and manufacturing engineering of combination die which was made up of steel-bonded carbide core and insert block were expatiated.
详细阐述了硬质合金模芯镶块剖分式组合凹模的结构和制造工艺。
The structure had advantages that: an assistant die sinking air cylinder is added on the down slide block which is helpful to the down slide die realizing die sinking.
以上结构的优点在于：在下滑块上增加一个辅助的开模汽缸，有 助于帮助下滑块实现开模。
When the utility model drives the upper punch die by the slide block to proceed with the working, the lower punch power is bigger.
本实用新型经滑块带动上冲模进行工作时，下冲力较大。
The process of raising a printed image using an un-inked block or die on paper or board.
用不着墨的电版或模在印有印纹的纸品上压成凸纹效果的方法。
The geometrical movement of the swaying block of the matrix is analyzed. The corresponding die structure has been designed. It can serve as a reference for forming similar parts.
分析了凹模摆块机构的几何运动，设计了相应的弯曲模结构，可为类似零件的成形提供参考。
Debossing: the process of pressing a recess image using an un-inked block or die on paper or board. It is the opposite of embossing.
压凹：用不着墨的电版或模在纸上压成凹纹效果的方法。是浮雕压印的相反。
As far as the practicability of the die for the thickness, the height of the block would be adjusted when extruding the sheets with different thickness.
考察了宽幅机头对于不同厚度片材的挤出适应性，得到结论：当生产不同厚度的片材时， 阻尼块高度需要调整。 关键词：高分子防水卷材，三维有限元，流场分析，挤出机，机头。
Source of aluminum model: self-check die-block equipped by DPX-MD dual-energy X-ray bone densometer produced by American LUNAR Company.
铝体模来源：美国LUNAR公司生产的DPX - MD双能X射线骨密度仪所配备的自检模块。
The flanging-sizing die structure of the exo-skeletal was improved, using auto-half block, solved the difficult problem of part out off die.
改进了的旧的骨架翻边整形模，采用自动哈夫成形，解决了零件出模困难的问题。
The paper presents the gauge block punching technique and the die structure.
介绍了卡板的冲压工艺及模具结构。
The structure and design method of typical bending slide block using in punching die were introduced.
针对锁紧片零件，设计了折弯压凸复合模，并介绍了模具结构和工作过程。
The manufacturing method of the magic block comprises such main operations as material preparing, die stamping and perforating and protective layer painting.
所述魔块的制作方法包括备料、模压制孔、涂刷保护层主要操作。
The manufacturing method of the magic block comprises such main operations as material preparing, die stamping and perforating and protective layer painting.
所述魔块的制作方法包括备料、模压制孔、涂刷保护层主要操作。
应用推荐