Cycloidal tooth profile of the internal gear pump, also called cycloidal rotor pump, pump the small gear and internal gear only related a tooth, so the internal gear pump do not need to set partition.
摆线齿形的内啮合齿轮泵又叫做摆线转子泵，泵中的小齿轮和内齿轮只相关一个齿，因此这种内啮合齿轮泵不需要设置隔板。
Internal gear pump structure and other gear pump structure similar to, mainly by the outer rotor and rotor, pump shaft, pump body, the front cover, bracket, sealing device, bearing, etc.
内啮合齿轮泵的结构和其他齿轮泵结构类似，主要由外转子、转子、泵轴、泵体、前盖、托架、密封装置、轴承等组成。
Rationally define the work gear pump speed, gear and the axis of rotation to avoid engaging resonance frequency, can prevent noise intensified.
合理确定齿轮泵的工作转速，使齿轮与轴的转动避开啮合共振频率，可以防止噪声加剧。
This kind of gear pump return route's model application is on the engineering machinery Chang ke sees walks, the rotation gear, it saves a donkey pump.
此种齿轮泵回路的典型应用是工程机械上常可见到的行走、转向机构，它节省去一个辅助泵。
If the first gear pump operation, or long-term idle after use, preferably in small load or no-load circumstances Xianpao One hour.
齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。
These two kinds of internal gear pump working principle and external gear pump working principle the same.
这两种内啮合齿轮泵的工作原理和外啮合齿轮泵的工作原理相同。
How to choose the gear pump seals?
齿轮泵如何选择密封垫？
The gear pump seals the selection principle is not high demand, for the occasion, but by experience, not to replace timely selection.
齿轮泵密封垫的选用原则是，对于要求不高的场合，可凭经验选取，不合适时再更换。
Retention gear pump, motor and foot screws, screw the force should be uniform, reliable connection.
紧固齿轮泵、电动机的地脚螺钉时，螺钉受力应均匀，连接可靠。
Internal gear pump is the small gear wheel, the big gear for driven wheel, in work big gear with small gear cocurrent rotation.
内啮合齿轮泵中的小齿轮是主动轮，大齿轮为从动轮，在工作时大齿轮随小齿轮同向旋转。
High viscosity of the liquid transmission gear pump should be at a lower power consumption, less leakage, larger output under the pressure of the most traffic.
输送高粘度液体的齿轮泵应做到在较低的功耗、较少的泄漏、较大的压力下输出最多的流量。
KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal.
kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。
High viscosity gear pump does not generate pressure, it is only the output flow. Pressure is low or no pressure, high viscosity gear wheel pump don't inhale the liquid or leakage is serious.
高粘度齿轮泵并不能产生压力，它只是输出流量。压力低或无压力，说明高粘度齿轮泵没有吸入液体或泄漏严重。
Check valve and relief valve on the output of the gear pump tube had better install a check valve.
止回阀与安全阀在齿轮泵的输出管路上最好安装一个止回阀。
Gear pump with the direction of rotation into and out in line with the oil mouth.
齿轮泵的旋转方向要与进、出油口相符。
The product is applied to medium, high-pressure gear pump, ram pump, vane pumps, etc.
产品主要应用于中、高压齿轮油泵、柱塞泵、叶片泵等。
Multiple string option with our IPH series inscribed gear pump.
我们沉着症者齿轮泵系列多字符串选项。
Internal gear pump has two kinds of tooth profile namely: involute profile and cycloidal tooth profile.
内啮合齿轮泵有两种齿形即：渐开线齿形和摆线齿形。
Use of helical gear in gear pump is an effective measure, which can reduce the mechanical voice and flow pulse.
齿轮油泵采用斜齿轮是降低机械噪声和减小流量脉动的一种有效措施。
According to the volume oil formula of the straight gear pump, the volume oil formula of the helical gear pump is got and the helix Angle no trapping is found.
利用直齿齿轮泵的困油容积变化公式，求出了斜齿齿轮泵的困油容积变化公式，得到了斜齿齿轮泵不发生困油的螺旋角。
This article counter gear pump and hydraulic cylinder's appearance's common breakdown carries on the analysis.
本文对齿轮泵和液压缸的出现的常见故障进行分析。
The construction and principle of the balanced compound gear pump is introduced.
介绍了平衡式复合齿轮泵结构原理。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
齿顶高系数是设计齿轮时的重要几何参数，也是影响复合齿轮泵流量特性的重要参数之一。
Flexible set cycloid gear pump rotor pump vane pump with the advantages of a similar volume than pump more than 10% efficiency.
柔性摆线转子泵集齿轮泵与叶片泵优点于一身比同类容积泵的效率提高10%以上。
Develops a CAD system for gear pump design of locomotives.
研制了一个内燃机车用齿轮泵的CAD系统。
Comparing with involute gear pump, the instant displacement is in direct proportion to the angular velocity of the gear and stable without pulsation.
对比渐开线齿轮泵，单圆弧齿轮泵的瞬时排量与齿轮角速度成正比，且稳定，无脉动。
It makes grave effect to gear pump work stability and service life.
严重影响油泵的工作稳定性和使用寿命。
This article will discuss the design of compensating groove in external gear pump by analyzing the gearing characteristics.
该文主要通过分析齿轮的啮合特点来探讨啮合齿轮泵卸荷槽的设计。
Gear pump is a kind of spare parts for cranes.
齿轮泵是一种用于起重机的配件。
The interlaced gear pump is designed on the basis of analysing flow and pressure pulses.
本文在分析齿轮泵的流量脉动和压力脉动的基础上，设计出一种错齿齿轮泵。
应用推荐