Cycle polymer flooding method can reduce injection pressure.
周期注聚方式可以降低注入压力。
The injection pressure, timing, duration and rate depend on the engine speed and load.
喷油压力、喷油始点、喷油持续角和喷油率均取决于柴油机转速和负荷。
Finally, the injection pressure for the earthquake triggered by injecting water is considered.
最后，对注水地震的注水压力进行了讨论。
Influence of injection pressure and fuel temperature for standard fuel consumption was studied.
研究了喷油器开启压力和试验油温度对标准油量的影响；
The injection pressure rose, the injectivity profile and interlayer contradiction was modulated.
水井注入压力升高，吸水剖面得到调整，层间矛盾得到改善；
The injection pressure is commonly described as the surface pump pressure required to achieve injection.
注入压力普遍地是指实现注入所需的地面泵压。
Injection pressure in one of the major factors effecting the results of development of sandstone reservoirs.
注水开发的砂岩油田，注水压力的高低对油田开发效果有很大的影响。
Water injection efficiency depends on whether the injection pressure is high or low in water injection Wells.
注水井注水压力的高低直接影响水井的注水效率。
The influences of injection pressure and injection temperature, two important injection parameters, were studied.
研究了注射压力和注射温度这两个重要的注射参数对注射坯体质量的影响。
Anew forecasting method of wellhead injection pressure for polymer flooding is established based on Dupuit formula.
依据裘比公式建立了一种新的聚合物驱油井口注入压力预测方法。
The injection pressure of E30 engine corresponding to the lowest fuel consumption is higher than that of diesel engine.
E30的最低燃料消耗率对应的喷嘴启喷压力略高于柴油。
Theoretical result shows that even in a very low admixture injection pressure, fracturing will occur in surrounding soil.
理论分析发现即使在很小的固化剂注入压力作用下，周围土体也会发生劈裂现象。
The feature parameters extracted from the waveform of the full injection pressure reflecting typical faults are analyzed.
根据某自行火炮喷油压力的波形特点，分析确定了反映典型故障的特征参数。
During core flooding test, the influence of the injected medium on core permeability causes injection pressure to fluctuate.
在岩心流动试验过程中，注入介质对岩心渗透率的影响必然会引起注入压力出现一定幅度的起伏。
The effects caused by injection pressure change in RIM are discussed. Suggestions for determining injection pressure are made.
探讨了注射压力变化引起的RIM工艺中的各种效应。提出了确定注射压力应考虑的事项。
In the function of injection pressure, the mould which has core will produce a little core offset and cause plastics deformation.
具有型芯的模具，在注射压力的作用下，将使型芯产生一定偏移，引起塑件变形。
Commonly used methods to evaluate the injectability included testing injectability coefficient, pushing force and injection pressure.
常用的注射性能评价方法包括测定注射能力系数、推力和注射压力三种。
Pollution in non-target zones can be reduced, the efficiency of profile control can be improved by using rational injection pressure.
合理的注入压力可减少对非目的层的污染，提高调剖措施的有效率。
This paper introduces the authors primary research results of the study of the DME spray characteristics under high fuel injection pressure.
介绍了在高压环境下对二甲基醚（DME）喷雾一般特性的试验研究结果，并与柴油的喷雾特性进行了比较。
Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.
加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。
It's the first time to question extensively the influences of fuel delivery advance Angle and injection pressure on performance of E30 engine.
首次系统地研究了供油提前角、喷嘴启喷压力对E30混合燃料发动机性能的影响。
As the injection pressure subsides, the mold begins to close to perform a coining operation, resulting in a strong, high yield carrier or lens.
随着注射压力的减小，模具开始闭合，进行压印操作，最终生产出高强度、高产量的载体或透镜。
The molder must recognize the dangers of excessive fill speed, insufficient injection pressure, excessive melt temperature, and inadequate packing.
注塑工必须认识过快填充速度、不足注塑压力、过高融化温度和不充分挤压的危害性。
Factors affect gas lift options: the yield of the well bottom-hole pressure, fluid production index, lifting height and the gas injection pressure.
影响气举方式选择的因素有：井的产率、井底压力、产液指数、举升高度及注气压力等。
As a result, it was found that injection speed could be increased through varying nozzle port opening width under keeping constant injection pressure.
实验结果表明，在压力恒定的条件下，可通过控制喷嘴开启量大小获得不同的注射充填速度。
Reasonable injection pressure and rate can improve the development response of gas injection and the recovery factor of carbonate buried hill reservoir.
筛选合理的注入压力、注入速度等参数，为预测注气开发效果、提高碳酸盐岩古潜山油藏开发后期采收率提供了依据。
Increasing the water injection delay time and water injection pressure resulted in slightly decrease of the residual wall thicknesses of post-filled region.
提高注水压力与增加注水延迟时间时注水后填充部分的残留壁厚略有减小。
The lower injection pressure means that reduce the internal stress of products, and then makes products heat resistance and processing after won the bid up.
较低的注塑压力意味着减低了制品的内应力，进而使得制品的耐热性和后加工性获得了抬高。
Due to high water injection pressure, it is difficult to transport the logging cable into water injection WLL by its own weight during well logging process.
在注水井带压测试工艺中，由于注水压力的影响，测井电缆依靠自身质量无法向井下输送，为此开发研制了测井电缆带压下井输送器。
The effect of forming temperature, injection pressure and piston velocity on the filling ability of semi-solid A356 aluminum alloy slurry were investigated.
研究了半固态A356铝合金浆料的成形温度、压射比压和压射冲头速度对半固态A356铝合金流变压铸充填性的影响。
应用推荐