The assembly property of plastic air intake manifold is researched.
使设计开发的柴油机塑料进气歧管在装配性上是良好的。
At least 5 years experience on intake manifold and cylinder cover; 4.
从事汽车进气歧管、气缸罩盖设计经验五年以上;
Compressed air is injected at the left end of the intake manifold tube.
压缩空气注入在左端进气歧管管。
The intake manifold connects the carburetor to the intake ports of the engine.
进气歧管把发动机进气道口连接起来。
The picture below shows the timing shaft, timing gear and the intake manifold.
下面的图片中显示的时间轴,齿轮和时间的进气歧管。
A component, such as an intake manifold or a throttle body, has an air passage.
一种部件,例如进气歧管或节气门本体,具有空气通道。
First, the structure and function of the engine air intake manifold are analyzed.
首先对发动机及其进气歧管的结构功能进行了分析。
The injection molding is an important tache to exploit plastic air intake manifold.
注塑成型工艺是开发塑料进气歧管的重要环节。
If the engine backfires, the sudden pressure in the intake manifold forces the valve back.
如果发动机回火,进气歧管骤增的压力就迫使阀门向后移动。
Nick set one end of a long socket extension on the intake manifold and listened to the other end.
尼克拿过来一根螺栓套杆,把一头儿贴在进气歧管上,然后凑过去听了听另外一头儿。
When the engine is shut off, the intake manifold cools and a slight vacuum forms as a result .
这是因为当发动机熄火时,进气歧管冷却而产生轻微的真空。
Summarized some important experience on designing injection mould of plastic air intake manifold.
总结出了在设计塑料进气歧管注塑模具时要注意的几个问题。
This device, called the manifold heat-control valve, is built into the exhaust and intake manifold.
这种装置称为“歧管热控制阀”,它拼装在排气与进气歧管中。
The air filter is usually located in the air stream to your throttle valve assembly and intake manifold.
空气滤清器通常位于空气流到你的节流阀总成和进气歧管。
The piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum.
活塞主要因进气歧管真空度的变化而在活塞腔内上下移动。
Fuel injectors pulse to follow engine firing order, in accordance with engine demand, on a tuned intake manifold.
按照引擎的要求,燃料注入器在一个受到调整的进流管上进行脉动注入,以跟随引擎的点火顺序。
Install cylinder head, intake manifold, and exhaust manifold, refer to cylinder head installation in this section.
安装汽缸盖,进气歧管和排气管,请参阅本部分的汽缸盖安装。
The fuel system only has several major parts such as fuel tank, fuel pump, fuel filter, carburetor, intake manifold, etc.
燃料系只有这样几个主要部件,如燃油箱、输油泵、燃油滤清器、化油器、进气歧管等。
The Throttle body provides surfaces for mounting between the Motorcycle's air intake duct and the engine intake manifold.
风门表面留有安装摩托车进气管和发动机进气歧管的位置。
The second part carries on the air fluid simulation analysis of variable intake manifold with the STAR-CD fluid software.
第二部分用STAR - CD流体软件对可变式进气歧管进行空气流动数值模拟分析。
The company has many years of production muffler intake manifold assembly, bellows, metal hose of professional experience.
公司有多年生产消声器进气管总成、波纹管、金属软管的专业经验。
The intake manifold pressure is lower when the cranking speed increases, thus the fuel metering strategy should be modified.
随着拖动转速升高,进气歧管压力降低,对应的喷油策略也应随之调整;
This paper introduces the calibration system and static and dynamic calibration method of an engine intake manifold pressure sensor.
介绍了发动机进气歧管压力传感器的标定系统和传感器静、动态标定方法。
Additionally I further improved the oil and air mixing by producing a special "intake manifold" So the oil is broken up more finely.
此外,我进一步提高石油和空气通过产生一种特殊的“进气歧管因此,石油被打破了更为理想的”混合。
With the redesigned valves, the engine is not sensitive to air pressure and will easily run just by blowing into the intake manifold.
由于重新设计的阀门,发动机不敏感,空气压力,将很容易运行只需吹的进气歧管。
Engine fittings series:Gear chamber, Cavaera cover, Sprocket rooms cover, Preheaterbase, Water pump Cover, Intake manifold, Pump box.
发动机配件类:齿轮室、气门室罩盖、链轮室罩盖、预热器座、水泵泵盖、进气歧管、泵箱;
A single 52mm throttle body sits atop a plastic intake manifold and feeds a common chamber, which in turn feeds six long intake runners.
一个单一的52mm油门机构坐落在一个塑料进气歧管,养一个共同的工作室进而促进六长进气赛跑选手。
Load change in the engine intake manifold pressure changes that is when the spool displacement greater, gas output in response to faster.
在发动机负荷变化即进气管压力变化时,阀芯的位移更大,燃气输出量的响应更快。
In order to improve engine efficiency and torque as well as the engine performance, plastic intake manifold was developed for CA4GE engine.
为了提高发动机的效率和扭矩、改善发动机的性能,针对CA4GE发动机研究、设计、开发了发动机塑料进气歧管。
In order to improve engine efficiency and torque as well as the engine performance, plastic intake manifold was developed for CA4GE engine.
为了提高发动机的效率和扭矩、改善发动机的性能,针对CA4GE发动机研究、设计、开发了发动机塑料进气歧管。
应用推荐