你在哪里学会的焊接技术？
The crisis helped to weld the party together.
这场危机促使整个党紧密地团结在一起。
It's possible to weld stainless steel to ordinary steel.
将不锈钢和普通钢焊接在一起是可能的。
Re-weld the broken joint, please.
把开裂的接缝重新焊一下。
It can occur in any part of the weld.
它可能发生在焊接的任何部分。
Can you spot weld a tube to a sheet metal?
你能把一个钢管点焊到钢板上吗？
Weld identification single hole punch.
鉴别焊缝的单孔冲压机。
A: Can you spot weld a tube to a sheet metal?
你能把一个钢管点焊到钢板上吗？
The weld tool is just behind the corner!
焊接工具在拐角处！
It takes speed to weld steel at this heat.
在这样的高温下熔接钢铁需要快速。
Increase height to fit above other weld symbol.
增加高度以配合其他焊接符号。
Make sure the pieces you are about to weld fit together.
确认要焊接的管件都般配。
Weld the main gusset as shown in the drawing above.
焊接主要扣板如上所示在提请大会。
It takes speed and skill to weld steel at this heat.
在这样的温度下焊钢需要速度和技术。
Broken parts can be rejoined by drawing a plastic weld.
残破的部分可以通过绘制一个塑料熔接重新加入。
You can weld with it and cut through just about anything.
您可以焊缝与它穿过只是任何事情。
If the weld is done well, it is impossible to pull apart.
如果焊缝是做不好，这是不可能退出，除了。
Place identical weld beads on the opposite side of the gusset.
扣板相同的地点对面焊珠的。
We need people in a facility who can weld, who can repair things.
我们的工厂需要懂得焊接和修理东西的人。
The cross connection point of the round steel should weld fastness.
圆钢的交叉连接触应焊接牢固。
Use the drawing below to place the pattern of remaining weld beads.
使用焊接珠绘图下面其余地方的模式。
Too high switch point: empty part, weld line, sink mark, and small.
转压点太高：产品充模不足，熔接痕，凹陷，尺寸偏小等。
The results show that the steel has low weld cold crack sensitivity.
结果表明，该钢具备低的冷裂纹敏感性。
Weld Area crack. A crack in or immediately adjacent to the weld line.
焊缝区裂纹。在焊缝线或紧靠焊缝线出现的裂纹。
Spot-weld the side wind ow aperture to the inside of the side section.
将侧窗接缝点焊到侧面部件内侧。
The solution was drawn from the weld flux and proofed in the practice.
从焊剂方面提出了解决问题的方法，并在实际生产中验证了其使用效果。
Once the assembly is situated and held in place, weld it as shown below.
一旦大会和地点是位于举行，焊接它如下所示。
Once the assembly is situated and held in place, weld it as shown below.
一旦大会和地点是位于举行，焊接它如下所示。
应用推荐