在工艺参数更改前是否作试验。
Is there any experiment conducted before process parameter change.
通过正交实验得出最佳工艺参数。
The process parameters were optimized through orthogonal experimental design.
泥料的可塑性是最重要的工艺参数。
The mud plasticity is the most important technical parameter.
研究了连续操作时的最佳工艺参数。
The optimal operation parameters of continuous production were studied.
所得结果有助于工艺参数的优化设计。
All the results are helpful for process parameter optimal design.
提出了最佳工艺组合和主要工艺参数。
Technology-combination and main parameters were put forward firstly.
另外，还对MA的工艺参数进行了研究。
通过切削试验，确定了合理的工艺参数。
Appropriate processing parameters are established through cutting test.
制定拉丝线生产工艺参数。
提出了可行的生产工艺和正确的工艺参数。
The feasible process and correct technological parameters are given.
在此基础上，获得了最佳的工艺参数组合。
On this basis, the optimal process parameters combination are obtained.
并获取了使得收缩最小的最优工艺参数组合。
And the optimal combination of process parameters of minimum contraction is obtained.
获得了主要工艺参数。
切削过程为复杂的随机过程，工艺参数较多。
The cutting process is the complex and stochastic process, there are many craft parameters.
在最佳工艺参数下脱硫效率可以达到95%。
Under the best technical parameters the desulphurization rate can reach 95%.
进一步研究了萃取工艺参数对分离效果的影响。
The effect of operation parameter on separation method is further studied.
并对其工艺参数的影响和生产原理进行了讨论。
The influence of the process conditions and the principle of preparation were discussed.
负责工艺参数文件/作业指导书的制定和维护。
研究了工艺参数选择计算、模具设计和质量控制。
The selection and calculation of process parameters, die design and quality control are studied.
提出了合理的可以保证氧化铁粉质量的工艺参数。
The reasonable technical parameters were put forward to ensure the quality of ferric oxide powder.
对影响油炸薯片产品品质的工艺参数进行了研究。
The dynamic relationship between deep-frying process and quality change of fried food was investigated.
采用该工艺参数，切割出了高质量的心血管支架。
The high quality coronary artery stents have been cut with the output power o...
介绍了板式酸冷却器的结构、工艺参数和运行情况。
The construction, process parameters and operation of plate acid cooler are introduced.
因此，必须考虑其影响来综合制订热处理工艺参数。
We must determine the heat-treatment technical parameters, according to its influence.
文章还介绍了该技术的工艺参数，生产流程和装置。
The paper has reported technics parameter of the technology, production flow and the device too.
分析了影响熔喷非织造布过滤性能的主要工艺参数。
Study on the performance of filtration by uniform quartz sand media;
研究了工艺参数对熔覆合金层的组织和耐磨性的影响。
Effect of process parameter on microstructure and wear resistance of the coatings were studied.
分析了影响烘干效果及产品质量的几个主要工艺参数。
Several main process parameters, which influence the drying efficiency and product quality are analyzed.
产品的质量目标和性能指标、技术参数、工艺参数等。
Quality objective and performance indicators, technology data and process data etc.
此外还定制了通用工艺参数，以实现切削速度的优化。
Besides, some common technical parameters are customized to optimize the cutting speed.
应用推荐