The pneumatic circuit and the PLC-based control system are designed.
设计了气动控制回路和PLC电气控制程序；
Finally, the design of an under-actuated manipulator which is driven by pneumatic circuit has been finished.
最后，设计了一个利用气压回路驱动的欠驱动机械手。
Finish the pneumatic design of all the functions of hill-drop drill, and produce the pneumatic circuit drawings.
对气动部分的各种功能进行了设计，并绘制出气动回路图。
In the design section an under-actuated manipulator which is driven by parallel pneumatic circuit are presented.
在设计部分中则提出了一种利用并联气压回路驱动的欠驱动机械手。
Meeting all kinds of working conditions and forms of pneumatic actuators in the machine, a simple and reliable pneumatic circuit is put forward.
针对本机床中气动执行元件的不同工作条件和形式设计了简单可靠的气动回路。
In this paper, the expert system using Fuzzy Neural network to detect and diagnose faults is put forward through research on pneumatic circuit of assembly lines.
本文通过对气动生产线回路故障特点的研究，提出模糊神经网络故障诊断专家系统的诊断方法。
This article introduces the pneumatic control circuit, its design and characteristic.
本文介绍该自动线的气动控制系统、气动回路设计及其特点。
The paper introduced a particular pneumatic control circuit to open and close the boiler lid.
本文介绍了开闭蒸锅盖的一种特殊的气动控制回路。
It describes the designing, logic circuit, working principle and adjustment of the pneumatic rubber plate logic control system attached to the horizontal multiple-hollow-chisel mortiser.
详细阐明卧式多头打眼机气动膜片逻辑控制系统的设计，逻辑线路，工作原理及其调试。
The design idea and steps of one new type design method for pneumatic sequence circuit are concerned in this paper.
介绍了一种新型的气动程控回路快速设计法的设计思想和步骤。
These applications are typically located in pneumatic valves, printed circuit boards, gaming industry, and many environmentally friendly applications.
典型的应用包括：气动阀，印刷电路板，游戏工业和许多环保应用领域。
Firstly, based on the theory of pneumatic system design, the arithmetic of cylinder's diameter and the basis of components selection in charging (discharging) circuit are analyzed.
从气动系统设计的原理着手，分析气缸缸径的计算方法及进（排）气回路中气动元件的选型依据；
The pneumatic control circuit, which is consisted of the pressure regulator component, the direction valve and the cylinder, is the most commonly used circuit in the industrial automation.
气动自动化系统是实现传动与控制的主要方式之一，其中由稳压元件、换向阀和气缸等所组成的气动控制回路更是工业自动化中常用的回路。
The metal and non-metal of comminuted printed circuit board scrap was studied by the method of pneumatic separation, comminuted material were separated according to density and size by wind power.
利用气流分选的方法对粉碎后的废弃印刷线路板中的金属与非金属进行了研究，粉碎后的颗粒在气流作用下按照密度与粒度进行分选。
Check the equipment controlling circuit and clean the contacting places. Check the pressure and valve, and if the pneumatic controller is working normally.
检查电器控制线路并清洁其接触点，查看各气压，气阀；气动控制器是否正常。
An effective mechanical process including impact crushing and pneumatic separation for metal recovery from printed circuit boards scraps was investigated.
采用冲击破碎和气流分选技术对废线路板的机械分离过程进行了研究。
Function and principle of the pneumatic control of plane refueller had been related simply. Methods of removing gas circuit troubles had been recommended.
简述了飞机加油车气控功能及原理，介绍了气路系统故障的排除方法。
This research is based on development of the present work on pneumatic manipulator system, describing at length the construction, circuit diagram and gas circuit of the manipulator system.
文章在现有研究工作基础上，对气动机械手系统进行研究，对系统的结构、电气路设计进行了详细描述。
Otherwise, this paper also designs conveyor 's in-phase air controlled circuit which relates to pneumatic balance system.
另外本论文还设计了与气动平衡相关的输送机同步机构气控回路，完善气动机械手的功能。
With the wide application of electro-pneumatic and electro-hydraulic control systems in engineering vehicles, it is becoming more important to resolve control circuit faults.
在工程车辆电控气动和电液控制系统的广泛应用，它已成为更重要的是解决控制电路故障。
The pneumatic separation technology for the separation and enrichment of metal in the waste printed circuit board scraps is investigated.
采用气流分选技术对破碎解离后的废弃印刷线路板进行分离富集，重点考察了不同粒径下气流分选富集金属的效果。
The pneumatic separation technology for the separation and enrichment of metal in the waste printed circuit board scraps is investigated.
采用气流分选技术对破碎解离后的废弃印刷线路板进行分离富集，重点考察了不同粒径下气流分选富集金属的效果。
应用推荐