Then discuss the power drive circuit and the logic control circuit in detail.
并详细介绍了功率驱动电路及逻辑控制电路。
Presents the control principle of electromagnetic bearing and the requirements of the power drive circuit.
介绍了电磁浮轴承的控制原理及对功率驱动电路的要求。
To control stepping motors, the balance bridge power drive circuit is made up by TDA1521 integrated audio power amplifier, the pulse allotter is made up by the parallel ports of computer and latches.
双回转机构的步进电机控制电路由TDA1521音频集成功率放大器组成平衡桥式功率驱动电路，由计算机并行口经过锁存器构成脉冲分配器。
Input power over the impact of power will often form a drive circuit driver chip damage, as well as passive components such as passive breakdown breakdown.
输入电源的过电冲击常常会形成驱动电路中驱动芯片的损坏，以及电容等被动元件发作击穿损坏。
IGBT drive circuit performance analysis, to do motor control or power of the people very useful.
IGBT驱动电路性能分析，这对做电机控制或电源的人来说很有用。
The entire drive circuit has characteristics of sample construction, powerful drive energy and low consumed power by using IR2110 as the drive modular.
采用IR 2110作为该功率放大电路的驱动模块，构成的整个驱动电路具有结构简单、驱动能力强、功耗低的特点。
A new "phase shift type" vernier drive circuit which provides the analog power for step motors is presented in this paper.
本文提出了一种新型的“移相式”微步驱动电路，该电路向步进电动机提供一个模拟电源。
The third chapter mainly introduces the hardware design of soft starter, including the main circuit, control circuit, drive circuit, and protect circuit and auxiliary switched power design.
第三章详细介绍了软起动控制器的硬件设计，包括主电路、控制电路、驱动保护回路和辅助开关电源电路的分析和设计。
A new drive circuit for IGBT is designed. It features high switching frequency, high driving power, simple-structure and reverse-turn-off.
论文中还设计了一种新型的IGBT驱动电路，它具有开关频率高、驱动功率大、结构简单且具有负压关断的特点。
A novel power conditioning circuit for flux compression generators (FCG) to drive high impedance loads is presented.
爆磁压缩发生器一般具有较低阻抗，在驱动较高阻抗负载时需要脉冲功率调制电路。
The power supply module provides the control circuit, the drive of frequency conversion circuit, transaction circuit and DSP with different power supply.
电源模块为系统控制电路、变频驱动电路、变送电路、DSP芯片提供不同要求的电源。
This article presents a design of permanent magnetic brushless DC motor control system and mainly involves the hardware circuit design of speed closed loop and power module drive.
介绍了一种永磁无刷直流电机控制系统的设计方案，主要涉及速度闭环和功率模块驱动的硬件电路设计；并通过实验证明该设计可直接用于小型无刷直流电机的控制。
This thesis pays more attention to the drive circuit of high frequency power MOSFET, power regulation circuit and frequency-tracing circuit.
本文主要研究高频功率MOSFET的驱动电路、频率跟踪电路以及功率调节电路。
An excitation control circuit tor direct current drive system of large power shovel has been designed.
本文设计了大型挖掘机直流传动系统的激磁调节电路。
Unique circuit design, using high-performance constant-current drive power, thereby achieving a highly efficient energy-saving purposes.
独特电路设计，采用高性能恒流驱动电源，真正达到了高效节能的目的。
It introduces a simple drive circuit, which can improve dynamic performance of welding power source, lower the manufacturing cost and meet the requirement of GB15579.
介绍了一种简单的驱动电路，它能有效改善焊接电源的动态性能，降低产品制造成本，满足GB 15579的安全要求。
Unique circuit design, using high-performance constant-current drive power, really reached efficient energy-saving.
独特电路设计，采用高性能恒流驱动电源，真正达到了高效节能的目的。
The basic program is that in the wiper circuit the power transistor and relay are connected in series to perform drive control.
主要方案是，在刮水装置回路中串接功率三极管或继电器实行驱动控制。
Temperature control circuit, in the case of low water temperature, can cut off the drive power protection device, in the case of high water temperature, open the cooling fan cooling.
水温控制电路，能在水温低的情况下，能切断驱动电源保护装置，在水温高的情况下，开启散热风扇散热。
The drive circuit of power MOSFETs is simplified and the stabilization of the controller is enhanced attributed to the drive capability of this chip.
由于芯片自带功率MOS管驱动能力，简化驱动电路设计的同时提高了控制器的可靠性。
The stroboscopic light source made of high-power LEDs (higher than 5w) not only can replace the mercury stroboscopic light source, but also can greatly simplify the drive circuit.
采用5w以上的大功率LED构成频闪光源，不仅可以完全替代汞灯频闪光源的功能，而且驱动电路还可以大大简化。
This paper studied control system with the center of SPCE061A MCU, including the drive and soft-start circuit of two power supply, the key and distance control of the cleaner.
以SPCE061A单片机位核心，研制了高效、适用的控制系统，包括两个电源的驱动、软启动、净化器的按键及遥控等电路。
When designing the step motor drive circuit of 5 phase 10 pat, 89c2051 is adopted as the Loop allotter. The VMOS is adopted in power elements. It is designed as chopper-type constant current circuit.
设计五相十拍步进电动机驱动电路时选择了89c 2051作为环形分配器，而功率器件选用电压型的VMOS管。
The flyback mode switch power supply is chosen as the main circuit of the high voltage power in the paper with 555 pulse control circuit and flyback drive circuit.
选择了反激式开关电源作为高压电源的主电路，并以555脉冲控制电路和反激式驱动电路作为辅助电路。
Usually LED power and drive damage from the input power over power shock (EOS) and load side circuit fault.
通常LED电源和驱动的损坏来自于输入电源的过电冲击(EOS)以及负载端的断路毛病。
The main control circuit sends 6 PWM signals. After the isolation and enlargement by the power circuit, these signals could drive the Permanent Magnet Synchronous Motor (PMSM for short).
主控电路发出6路PWM信号，经过功率电路隔离和放大，驱动交流永磁电机运转。
The system has been applied to the training system for electric drive system of DF4D and DF11 locomotive as well as for the circuit of 25k air-conditioner power generation car.
该系统已在DF4D型、DF11型机车电传动培训系统和25K空调发电车电路培训系统中得到正式运用。
The system hardware architecture is divided into control, drive, power supply, display five blocks circuits, and magnetic coupling is used to isolate circuit boards.
系统在硬件结构上分为控制、驱动、电源、显示、电压转换五大模块电路，各电路板之间采用磁耦进行隔离。
The system hardware architecture is divided into control, drive, power supply, display five blocks circuits, and magnetic coupling is used to isolate circuit boards.
系统在硬件结构上分为控制、驱动、电源、显示、电压转换五大模块电路，各电路板之间采用磁耦进行隔离。
应用推荐