Photo 1 shows the rocker arms with the rocker arm pins and ball bearings installed.
图片1显示了摇杆武器与摇臂引脚和球轴承安装。
One of the heads with rocker arm brackets and spark plugs installed.
其中一名负责人与摇臂括号和火花塞安装。
Inside the pump, a flexible diaphragm connects to the rocker arm though a diaphragm spring, pull rod and link.
油泵中可变形膜片的泵膜通过膜片回位弹簧和膜片拉杆与摇臂相连。
The "EPG" (two jaw) and "ETG" (three jaw) parallel gripper lines utilize a double acting piston and rocker arm design.
在“电子节目指南”（两个下巴）和“ETG的”（三下巴）爪平行线利用了双动活塞和摇臂的设计。
Install the hydraulic tappets and rocker arm.
安装液压挺杆和摇臂。
This setup shows the radius on the end of the rocker arm brackets being cut using the rotary table.
这表明，半径设置的结束摇臂括号被削减使用转盘。
The finished rocker arm brackets.
成品摇臂括号。
To raise the polishing efficiency of Cubic boron nitride (CBN) superhard material, crank rocker arm mechanism has been developed by using Computer Simulation Technology.
为了提高立方氮化硼超硬材料的抛光效率，采用计算机仿真技术开发了曲柄摇杆抛光机构。
We currently offer five main product lines of valve guide, rocker arm, precombustion chamber, valve seat insert and rocker shaft.
我公司现有产品包括气门导管、气门摇臂和预燃烧室、气门座、摇臂轴总成各大系列品种。
The CAM follower rides against a push rod, which pushes against a rocker arm.
凸轮挺杆推动控制摇臂的推杆。
The downward-moving side of the rocker arm pushes on the valve stem to open the valve.
摇臂向下移动的那一边推动气门杆以打开气门。
If valve clearance needs to be adjusted, loosen the locknut on rocker arm adjusting screw. Turn adjusting screw until feeler gauge slips with a slight drag.
如果气门间隙需要调节，松开摇臂调节螺丝上的防松螺母，转动调节螺丝直到测隙规滑动时稍带阻力为止。
This paper expounds the design method of the rocker arm with low rotating inertia and rotating inertia measuring method of the special rocker arm.
本文论述了低转动惯量摇臂的设计方法及异形摇臂转动惯量的测试方法。
Taking the rocker arm of trailer concrete pump as a typical example, application of nc electric-spark line-cutting to female spline machining is described.
以混凝土拖泵中的典型零件——摇臂为例，介绍数控电火花线切割在内花键孔加工中的应用。
In this thesis, the equations have been set up through treating bearings of rocker arm as elastic component.
本文将转臂轴承视为弹性环节建立并提出适合于这类传动的变形协调普遍方程。
Motion state of the plate turnover machine of gear drive type, double-arm crank rocker type and hydraulic type has been analyzed deeply.
对齿轮传动式、双臂曲柄摇杆式、液压式翻板机的运动状态进行了较深入的分析。
The mute rocker arm, less noise.
静音摇臂支撑结构，噪声更低。
Common defects during the rocker arm production were analyzed and some measurement was suggested.
同时，分析了摇臂铸件在生产过程中常见的缺陷，并提出了改进措施。
Average type beam drill is composed of base, inside and outside column, rocker arm, main spindle box and job.
普通型摇臂钻床由底座、内外立柱、摇臂、主轴箱及工作组成。
The push rod, as it is lifted, causes the end of the rocker arm to move up.
当推杆升起时，摇臂的端部向上移动。
On the basis of kinematics and geometry principle, the mathematical model for the double rocker arm mechanism was established.
用这种方法设计的双摇杆导引机构能满足平管机械对较大直线位移的运动要求 。
The rocker arm pivots around its supporting shaft so that the valve end of the rocker arm is forced downward.
摇臂围绕支承轴旋转，气门与摇臂相对应的一端压下。
The contribution of engine reliability design to environment protection is illustrated with a case of rocker arm bushing design.
通过发动机摇臂衬套的可靠性设计案例分析，介绍了提高发动机可靠性设计对环保的贡献。
The article is concerned with the structural characteristics, and the test technique for the performance of an automatic self-locking, two fulcrum revolving tipper with rocker arm.
本文研究了二支座摇臂自动压车的旋转翻车机结构特点、设计计算和测试技术等。
The design of a rocker arm with low rotating inertia is one of the important development trends of the valve timing system structural design for a modern high -speed internal combustion engine.
低转动惯量摇臂的设计是近代高速内燃机配气系统结构设计的重要发展趋势之一。
The rocker arm on the jacket launch barge is a transition installation equipped at the stern.
导管架下水驳船摇臂是安装在船艉的用于导管架滑移下水的过渡装置。
With an adjustable crank pin to control the length of stroke. As the bull gear rotates, the rocker arm is.
惠氏机构的电机转动重载齿轮，驱动一个带有可调整销钉的曲柄以便控制进、回程的长度。
Based on the trait of the motion of the rocker arm after jacket launching, the impact of the rocker arms on the barge was firstly studied in this paper.
本文在阐述摇臂在导管架下水后的运动特点的基础上，首次进行了摇臂回转撞击驳船尾部甲板的研究。
Some castings, such as crankshaft, rocker arm et al were produced.
已浇注了曲轴、摇臂等铸件。
Some castings, such as crankshaft, rocker arm et al were produced.
已浇注了曲轴、摇臂等铸件。
应用推荐