The paper introduced a spinning model surface pressure measurement sy which used in the wind tunnel.
本文介绍了可用于测量风洞中旋转模型表面压力分布的集成测试系统。
The paper describes the measurement method for model surface temperature and model surface illumination strength in wind tunnel optical pressure measurement test by the virtual instruments.
本文介绍了在风洞光学测压试验中应用虚拟仪器技术对模型表面温度和模型表面光照强度的测量方法。
The pressure field measurement results on the wing surface of airplane model by luminescence pressure sensor (LPS) technique and classic tap technique in high speed wind tunnel are presented.
介绍了国内首次在高速风洞中使用荧光压力传感器(LPS)技术对飞机模型机翼表面压力场测量的初步结果。
The instantaneous wind pressures on the model surface were obtained from the synchronous multi-channel pressure measurements.
模型表面的瞬态风压利用多通道同步压力测量而得到。
The influence of clearance between the nozzles and the model of the surface pressure was used in the hybrid extended-range technique of the side back jet.
在风洞实验中采用纹影照相和压力分布相结合的实验方法，确定了侧后向喷流复合增程技术中喷嘴—模型之间间隙的大小对表面压力的影响。
The experimental result shows that the normal pressure distribution on the surface of the model blade is a conicoid, the maximum of the normal pressure is in the middle of the model blade.
研究结果表明，法向压力在模型铲刀表面呈二次曲面分布，在模型铲刀的中部取得最大值。
From the point of gasification of impurity, we have analyzed the formation mechanism of bubbles in the surface of films using model of a spherical shell which endures high inner pressure.
从杂质气化的角度，应用弹性力学的球壳受压膨胀模型，分析薄膜表面鼓包的形成机制，同时得到了相应情况下薄膜的损伤机制。
The ground pressure distribution and the shape of failure surface by conducting model tests for the cylindrical retaining wall of a shaft in cohesionless soils are discussed.
讨论了无黏性土中圆柱型挡土墙的模型试验，给出土压力的分布和破坏面形状。
Using surface contact model between stator and rotor, the pressure equalizing operation is realized.
采用定转子面接触模型，实现了电机的均压运行。
The distribution of wind pressure on every surface of the building was measured by a static model, and the static wind load was calculated.
通过测压模型风洞试验测量风压系数的分布，并计算静风荷载；
Then, a pressure-based height field fluid model is proposed and the pressure to simulate the fluid surface height is justified.
在此基础上给出基于压力高度域的水流模型，并阐述了该模型的合理性。
In the BEM model, the radiation impedance boundary condition at air intake surface is used and the results demonstrate that it is superior to the traditional pressure release boundary.
本文中空气入口边界采用辐射阻抗边界，优于传统的将入口边界压力当成零的软压力边界。
Based on the influence of stress sensitivity on the logging surface fracturing pressure, an interpretation model for…
该模型能成功利用压裂资料解释破裂压力，为地应力解释打下基础。
EF2300 model multi-functional curved surface positive-negative pressure machine can finnly adhere solid-woodveneer, heat transfer-printing film, decorative paper and PVC film on all kinds of material.
EF2300型多功能曲面正负压机，能够牢固地贴覆实木单板、压克力热转印膜、装饰纸、PVC膜于各种材料上。
EF2300 model multi-functional curved surface positive-negative pressure machine can finnly adhere solid-woodveneer, heat transfer-printing film, decorative paper and PVC film on all kinds of material.
EF2300型多功能曲面正负压机，能够牢固地贴覆实木单板、压克力热转印膜、装饰纸、PVC膜于各种材料上。
应用推荐