Pull the tip of the movable set so that the negative taper angle of the grinding easier.
活动式拉梢之设置使负推拔角之研磨更为方便。
This method is recommended for taper turning of external and internal surfaces when the taper Angle is relatively large.
当锥角相对较大时切削外锥面和内锥面推荐使用这种方法。
To make sure I got the taper Angle right, I would check by putting the rotary rasp behind the tip so I could just see the edges of it.
确认我的尖鹿角是正确的，我将通过把转动锉刀放在顶端后来检查它的边缘。
At present, the ring rolling technology roll one ring in one process, and the technology can't deal with stress focus on the sharp taper Angle of mandrel roller.
目前锥形套圈辗扩技术只能一次成形一件，而且由于锥形套圈锥角使得芯辊应力集中严重。
For grinding HSS and carbide engraving cutter as well as single lip or multiple lip cutters of various shapes such as radiused cutters or negative taper Angle of cutters.
该机可用于磨削各类形似半圆角或反锥角的高速钢和硬质合金雕刻刀具和单边或多边刀具。
To avoid sliding that occurs in cylindrical roller thrust bearings, the taper Angle of the rollers is selected so the extended contact lines intersect on the bearing axis.
为了避免推力圆柱滚子轴承发生滑动，滚子的锥度要合适以至于扩大的接触线可以与轴承轴相交。
The bearing contact Angle and the roller half taper Angle are two important parameters of a large taper conical roller bearing, they influence the load and life of the bearing.
轴承接触角和滚子半圆锥角是影响轴承载荷和使用寿命的两个重要参数。
The enhancement factor strongly depends on the illumination spot size, taper Angle of the probe, and the metal film thickness. The tolerance of the alignment Angle is investigated.
研究发现电场增强跟入射光斑大小，探针的锥形角，以及金属膜厚度密切相关。
By arranging the head part of the common magnetizer to be in a taper Angle shape, the clearance distance can be shortened, and the effective use length of the iron core is extended.
本发明将普通导磁体的头部设置成锥角形后，可缩短间隙的距离，延长铁芯有效使用的长度。
TAPER: any surface of any bearing part that is not the correct Angle or not to print.
锥度：任何轴承部件的表面角度不正确或者不符合图纸要求。
Taper roller bearings of the series 313 are particularly adequate due to their comparatively large contact Angle (approximate 30 deg), when high axial forces are to be considered.
圆锥滚子轴承系列313，特别是足够的，由于其相对较大的接触角(约30摄氏度)，高轴向力时要考虑的。
There is no common normal in the conical involute gear and the fixed chordal tooth thickness can not be measured accurately because of the coexistence of helix angle and taper.
渐开线锥形齿轮由于同时存在锥度和螺旋角，使得其固定弦齿厚无法精确测量，也没有公法线。
It will result in: increase of taper, inner corner Angle and camber is swept past outwards.
这种情况会造成：锥度增加、内棱角问题、弧形向外掠出。
This paper describes a new method and device for measuring helical line, pitch diameter, taper and half-angle of thread of petroleum thread gauges.
本文介绍一种测量石油螺纹量规的螺旋线、中径、锥度和牙形半角的新方法及装置。
The equations for thread taper, thread pitch, thread angle and height of thread can be derived on the base of fitted lines, which are accurate enough to meet the needs of industrial measurement.
该方法可测量螺纹的锥度、螺距、螺纹夹角和螺纹高度，测量精度可以满足工业测量要求。
This paper presents a method for machining of taper cutting tools with equal helix Angle. The principle of the method is using taper helical curve with equal pitch to approach equal Angle one.
文章提出了一种在经济型数控机床上实现等螺旋角圆锥螺旋线的加工方法，其原理是用等导程螺旋线去逼近此种曲线。
Taper Roller Bearings transfer the loads acting on the bearing at a certain angle, the so called alpha contact angle towards the shafts centre line, (see sketch below).
圆锥滚子轴承的负荷作用于轴承在某一个角度，即所谓的阿尔法对轴中心线的接触角，（参见下图）转移。
Meanwhile, we change the thread parameters, study the stress distribution caused by changing the pitch, taper and thread Angle, this work can provide a reference for manufacture.
同时改变钻具接头的螺纹参数，研究螺距、锥度、牙型角的改变对其应力分布的影响，为钻具接头的生产加工提供参考。
Probes of various structures, such as large cone angle and short taper or multi-taper, can be formed with the combination of the static and dynamical chemical etching methods.
利用此法可制备出尖端锐利、大锥角或多锥体等各种结构的光纤探针。
The Dynamic-Tilt jet cutter can position the nozzle at an fixed angle to cut , exactly offset the natural taper from the jet cutter.
“动态倾斜切割头”可把切割头定位在一定的角度去切割，能精确地抵消水刀切割所产生的自然倾斜角度误差。
The influence of sweep angle and taper ratio on the characteristics of wingtip stalling is discussed.
讨论了后掠角和尖削比这两个机翼外形参数对翼尖失速特性的影响。
The influence of sweep angle and taper ratio on the characteristics of wingtip stalling is discussed.
讨论了后掠角和尖削比这两个机翼外形参数对翼尖失速特性的影响。
应用推荐