Temperature cycling of components.
零件温度循环。
Result show that IMC layer increased with the cycles, and it grew faster under low temperature cycling.
结果表明，随着循环周期的增加，界面IMC层的厚度增加，且低温极限温度越低时IMC生长越快。
When hydride reorientation takes place, there is a threshold stress concerned with the number of temperature cycling.
随着应力增大和温度循环次数增加，氢化物再取向程度也增大，但是氢化物发生再取向存在应力阈值。
To provide the fan installed on the bicycle and its transmission mechanism, used to provide wind and temperature cycling.
提供安装在自行车上的风扇及其传动机构，用于给骑车者提供风力和降温。
With continuation of temperature cycling there is a reversible change of the shape(along curve 2) with a very small hysteresis.
在随后的温度循环中，其形状的变化是可逆的（沿曲线2），滞后效果很小。
Furthermore, stress strain distribution in the solder joints has dynamic feature during temperature cycling and is related to temperature history.
在温度历史过程中，应力—应变场等值分布图呈现动态特性，且与温度历史相关。
When applied stress is higher than the threshold stress, the level of hydride reorientation increases with the increase of stress and the number of temperature cycling.
当应力大于应力阈值时，氢化物应力再取向程度随着与应力、温度循环次数增加而增大。
RDP transducers are subjected to temperature cycling as well as electrical supply cycling, plus shock and vibration testing where application circumstances demand. RDP.
传感器受到温度循环以及供电单车，加上震动和振动测试在应用情况的需求。
The output power is very stable after the temperature cycling and vibration test. No apparent power decrease has been observed as the device working continuously for 500 h.
该光纤耦合模块连续工作500小时没有发现明显的功率衰减，并且输出功率经温度循环和振动冲击后具有较好的稳定性。
The basic properties of the new alloys shown here were fully characterized and their use in SMT applications evaluated, especially in drop shock and temperature cycling tests.
我们将介绍新合金材料的基本属性以及在表面贴装应用中的验证结果，特别是在跌落冲击和温度循环试验的结果。
These temperature cycling chambers feature the classic ESPEC look of stainless steel with a new, modern style. The adjustable controller pod will please users of different heights.
这些温度循环式的试验箱采用经典的的ESPEC不锈钢外观，但具有现代的款式。调节的控制器吊舱可满足不同高度的用户。
Based on pressure and high low temperature cycling tests and theoretic analysis, the threaded joint parts filled with sealing glue compound show excellent seal ability, and can be applied to SRM.
通过压力、高低温循环等大量的试验和理论分析表明：采用填充密封胶的螺纹联接密封结构具有优异的密封性，适宜在固体火箭发动机环境中应用。
Through appearance testing, X-Ray testing and temperature cycling testing, the reliability of mixed solder joints and lead-free solder joints which formed under various process parameters was assesed.
通过对不同工艺参数下形成的混合焊点和无铅焊点进行了外观检测、X射线检测和温度循环测试。
The incubation period of crack nucleation decreases and the crack propagation rate increases with the increase of thermal cycling temperature and cooling rate in the cycle.
随循环温度和冷却速率的增加，裂纹形核的孕育期缩短，裂纹扩展速率增加。
Thermodynamic principle of heat recovery system for low temperature waste heat with a given initial temperature and flow and for non-cycling operation is proposed in the article.
本文针对初温、流量一定且不循环使用的低温余热，提出确定其动力回收系统参数的热力学原则。
The application of dynamic strain ageing during cycling creep of Al-Mn alloys , consisting of various compositions, is studied at the middle temperature in this paper.
研究了不同成份的铝镁合金在中温和不同应力作用下的动态应变时效，并阐述了动态应变时效在循环蠕变中的作用。
The individual cycle-strain hysteresis loops were recorded, and the cycling response and high temperature low cycle fatigue life were obtained.
记录了各自的循环应力—应变滞后环，得出了试样的循环响应特征和各试样的高温低周疲劳寿命。
On repeated heating cycling through the switch temperature or above it, the room temperature resistivity rises and the PTC intensity decreases.
PT C材料经过在开关温度及其以上的较宽温度范围内重复热循环后，室温电阻升高，PTC强度降低。
The cycling Build-up removal air system make the material prewarming and keeping temperature.
采用内建式抽风系统循环应用，让受热体有预温，保温功用。
The thermal fatigue test was performed on 316 SS to understand the crack propagation behavior underthe cycling temperature environment.
从实用出发对316不锈钢管材进行了热循环下的裂纹扩展试验。
The Influence of Temperature, Barometric Pressure and Elevation upon Resistance for Cycling;
根据压力影响高度，即可计算上下两道环箍之间的合理距离。
The Influence of Temperature, Barometric Pressure and Elevation upon Resistance for Cycling;
根据压力影响高度，即可计算上下两道环箍之间的合理距离。
应用推荐