Describes a novel method of detecting for rotor flux position of the brushless DC motor (BLDCM).
介绍了无刷直流电机无位置传感器转子位置检测的一种新方法。
Finally, the optimum control for the brushless DC motor has been achieved by using microprocessors.
用单片机实现的无刷直流电动机特性的优化控制。
This paper describes a novel method of detecting for rotor flux position of the brushless DC motor (BLDCM).
介绍了无刷直流电机无位置传感器转子位置检测的一种新方法。
Through the operation on a computer, control instructions can be easily given to control the brushless DC motor.
通过操作计算机可方便地给出控制指令，控制电机工作在指定状态。
This is the brushless DC motor speed control procedures, written in assembly language. apply to TMS320LF2407A DSP.
这是无刷直流电动机调速控制程序，汇编语言编写，适用于TMS320 LF 2407a的DSP。
The control system for the brushless DC motor based-on 80c196mc consists of 80c196mc, IPM, speed displaying and speed setting module.
基于80c 196MC芯片的无刷直流电机控制系统，包括80c 196 MC、IPM、速度显示及速度设定模块。
Based on the linear time-varying MIMO mathematic model of the brushless DC motor, this paper proposed a method to design a speed observer.
基于无刷直流电机的线性时变多输入一多输出(MIMO)模型，提出一种速度观测器的设计方案。
This thesis is part of the project named "the controller of the Brushless DC Motor for electric-bike", which comes from the IT Special Fund of Dalian.
本课题源自大连集成电路设计产业化专项基金项目“电动自行车无刷直流电机控制器开发”。
The research achievement bring out a accurate efficient way to analyzeand design the brushless DC motor. It give much convenience to the motor designers.
本文的研究内容，对无刷直流电机的具体分析工具、方法作了进一步的探索，对设计、生产实践具有一定的现实意义。
The brushless DC motor has excellent characteristics of good start and timing performance, but it is a nonlinear system owing to commutation process and armature reaction.
虽然无刷直流电机具有良好的启动和调速性能，但是由于换相以及电枢反应等因素，它属于非线性系统。
Four PWM modes used in the brushless DC motor control system are introduced and their different influences on the commutation torque ripple of BLDC motors are analyzed in detail.
介绍了无刷直流电机控制系统中的四种PWM调制方式，详细分析了四种不同的调制方式对无刷直流电机换相转矩脉动的影响。
The structure peculiarity and design method of this brushless DC motor for HEV are introduced. It is shown that the design is rational by prototype trial of the brushless DC motor.
文章介绍了该混合动力电动汽车用稀土永磁无刷直流电机的结构特点和设计方法，通过样机试验验证了设计的合理性。
The Brushless DC Motor, important part of the system is well controlled including two-closed-loop control method, compensation for dead-time and analysis of fluctuation about swapping phases.
同时针对系统中的关键部分无刷直流电机采取了全面优良的控制策略，包括转速外环电流内环双闭环调速控制，死区补偿，换相脉动分析等。
A design of hybrid electric vehicle (HEV) brushless DC motor controller based on TMS320LF2407 with energy regeneration, which is used in the drive system of the HEV.
设计了以TMS320 LF 2407作为中央处理器的无刷直流电动机控制器，并将该控制器应用于混合动力汽车的驱动系统中。
For the control method of brushless DC Motor, it is very important to check that passing turns sub-position.
在无刷直流电机的控制中，转子位置的检测是至关重要的。
The PM brushless DC motor is a multi-variable and non-linear system.
永磁无刷直流电机控制系统是多变量和非线性的。
This paper intends to make a better on the Design of Brushless DC motor.
本文是对无刷直流电动机做出深入的剖析与设计。
Brushless DC motor from the stator core structure are divided into alveolar, a core non-alveolar, non-core non-alveolar and alveolar hollow stator Cup.
无刷直流电机从定子的结构来看分为有铁心有齿槽、有铁心无齿槽、无铁心无齿槽和无齿槽空心杯定子。
The position tracking controller with good performance is the guarantee of high precision brushless DC motor servo system.
为了设计高精度的直流无刷电机伺服控制系统，性能优良的位置跟踪控制器是其重要保障。
Discusses the problems existing in the door motor of elevator, puts forward the system project which takes DSP digital signal processing technology as core, DC brushless motor as driver.
探讨了目前电梯门机系统存在的问题，提出了应用DSP数字信号处理技术为核心，无刷直流电机为驱动机的系统方案。
The torque ripple caused by diode freewheeling of the inactive phase during non-commutation state of PM brushless DC motor(BLDCM)when using the PWM_ON type of pulse width modulation was analyzed.
分析了传统的PWM_ON调制方式对无刷直流电动机在非换相期间由于截止相的反并联二极管续流而导致转矩脉动的原因。
So, to use permanent magnetic brushless DC motor as the propeller of the ocean robot instead of the permanent magnet DC motor has a great significance both in theory and in practice.
因此，用无刷直流电动机代替永磁直流电动机作为海洋水下机器人的推进器，无论是理论上还是实际上都具有重大意义。
Carry out the debugging of a brushless DC motor control system hardware and software, meanwhile analyse and explain problems they encounter, at last putting up with solutions.
进行了直流无刷电动机控制系统的软、硬件调试，同时对调试过程中碰到的题目进行分析和阐述，并提出解决方法。
This paper analyzes the armature reaction of the brushless DC servo motor by means of finite element method (FEM), and points out that the armature reaction has great influence on torque ripple.
采用数值计算方法对无刷直流电机的电枢反应作了分析，指出了电枢反应对力矩波动的影响。
The system with CPU drives the DC brushless motor, and the encoder indicates the motor position outputting the sine and cosine signal.
系统采用CPU驱动直流无刷电机转动，编码器输出的正余弦信号指示电机的位置。
The software phase-locked loop (SPLL) technology in the steady speed control of permanent magnet brushless DC motor (BLDCM) in gyro was discussed.
研究了软件锁相环技术在陀螺用无位置传感器无刷直流电机稳速控制系统中的应用。
This paper introduces the suppression methods of spike current in the high voltage brushless DC motor controller based on MC33035.
介绍基于MC33035高压无刷直流电动机控制器尖峰电流的几种抑制方法。
This paper introduces the suppression methods of spike current in the high voltage brushless DC motor controller based on MC33035.
介绍基于MC33035高压无刷直流电动机控制器尖峰电流的几种抑制方法。
应用推荐