The transverse shear deformation effect is included by use of Mindlin-Reissner first-order shear deformation theory.
分析了计及高阶横向剪切变形的正交各向异性弹性板自由振动的问题。
The effect of diffusion controlled interfacial sliding on the transverse shear deformation of fibrous composites is studied.
研究了扩散控制的界面滑动对纤维复合材料的横向剪切变形行为的影响。
The effect of transverse shear deformation is considered and Angle of rotation of surface normal for each layer is different.
这类板的横向剪切变形效应必须予以考虑，因而层板不同层的表面法线的转角是不同的。
The examples show that the critical load of composite shells of revolution will decrease when considering the transverse shear deformation.
数值算例表明，对于复合材料旋转壳，横向剪切变形使其临界载荷降低；
The transverse shear deformation as well as extensional strain in each lamina is included. Equations of equlibrium for laminae are first derived.
在计算各单层横向剪切变形影响时，采用单层中面法线变形后维持直线，但放弃层中面法线及其正交线之间变形后保持直角的假定。
The analyses show that the transverse shear deformation effect has a significant influence on the thick reinforced concrete slabs and the concentrated load condition.
分析表明，横向剪切变形对钢筋混凝土厚板及集中荷载的影响很大。
The effects played by transverse shear deformation, panel geometric parameters, total number of plies, fiber orientation, and initial geometric imperfections are studied.
讨论了横向剪切变形，曲板几何参数，铺层数，铺展方式和初始几何缺陷等各种参数变化的影响。
The main advantages are the transverse shear deformation and rotary inertia are considered naturally, and there is no restriction on the thickness of plate and height of stiffener.
主要优越性表现为：结构的旋转惯性、剪切变形等都得到了考虑，且不限制结构的板厚度和加强筋的高度。
It is also seen that the transverse shear deformation and warping have effects on the aeroelastic stability of the rotor blade. These effects become larger at the higher thrust level.
同时对悬停时桨叶的气弹稳定性有相当程度的影响，尤其是在高桨距角下这种影响是不能忽略的。
This model is developed based on the one-dimensional SMA constitutive equation and multi-cell model, and considers the influence of transverse shear deformation of the hybrid composite beam.
采用多胞模型、形状记忆合金一维本构关系分析方法，同时考虑横向剪切的影响，建立了层合梁的数学模型。
This paper compared several mechanical models with transverse shear deformation and put forward a kind of layer model assuming that shear stresses vary parabolically through the plate thickness.
比较了考虑横向剪切变形的几种力学模型，提出了一种新的假定剪应力沿板厚呈抛物线分布的分层模型。
Besides the usual membrane stresses and stress couples the equation also contains additional terms reflecting the influences of transverse shear deformation, rotatory inertia and transverse extrusion.
该方程除了包含通常的薄膜内力项和内矩项外，还反映了横向剪切影响、转动惯性效应和横向挤压影响。
In the analysis of the stress and deformation under dynamic loading, the inertia force and damping moment should be considered in addition to the transverse shear effect.
在分析动载荷下的应力和变形时，除考虑横向剪切效应外，还须考虑微段的惯性力和阻尼力矩。
General analytic solutions for transverse bending of anisotropic rectangular plate using first order shear deformation theory is obtained at the first time by the complex series method (CSM).
采用复级数方法首次建立了基于一阶剪切变形理论的各向异性矩形板横向弯曲一般解析解。
General analytic solutions for transverse bending of anisotropic rectangular plate using first order shear deformation theory is obtained at the first time by the complex series method (CSM).
采用复级数方法首次建立了基于一阶剪切变形理论的各向异性矩形板横向弯曲一般解析解。
应用推荐