投料前期，要控制好入收尘器废气的温度和水分。
In the initial period of use, temperature and moisture content of the waste gas entering the bag filter should be well controlled.
探讨了温度、溶剂、投料比和反应时间对收率的影响。
The effects of temperature, solvent, material ratio and contact time on the yield were studied.
利用单体竞聚率差别，用一次投料法合成梯度共聚物。
The gradient copolymers could be obtained due to the difference of reactivity ratios of the two monomers.
考察了反应物投料摩尔比和反应温度对产物收率的影响。
The effect of molar ratio of reactants and reactive temperature on the yield of product is investigated.
这样急需一套简便的自动供胶控制系统来精确控制配比投料。
Therefore, it is of urgent demand to create a simple and convenient auto glue-supplying control system to accurately control the materials for confection.
根据中式菜肴的烹饪原理，规划了自动烹饪机器人的投料动作。
According to the principle of Chinese cooking, make out the automatic cooking robot's feeding action.
探讨了VTMS的投料比对聚合物的特性粘度和水溶性的影响；
The effect of VTMS on the intrinsic viscosity and solubility of the polymers is discussed.
在不同阻聚剂用量、投料比、投料方式等条件下合成环氧丙烯酸酯。
The epoxy acrylate was synthesized with different amounts of inhibitor, feed ratios and feeding modes.
锌熔炼炉自动投料系统可实现对熔炼炉投料的自动、定时、定量控制。
The zinc smelting furnace with automatic feeding system has functions of automatic, timing and quantitative control on its feeding process.
采用自动化机构PLC控制，自动投料，自动出料，方便可靠，故障低。
Controlled by the automatic mechanism PLC, it can feed and output automatically with stability and low failure rate.
讨论了投料比、反应温度和反应时间对收率的影响，并改进了合成工艺。
The effect on the proportion of materials, the temperature and the time to the yield are discussed, and the process of synthesis is improved.
进料方式采用分批加料的半连续方 式，其中一段投料量为20-80％。
Feed batch mode using a semi-continuous feed, which a quantity of 20 -80%.
二是工厂要健全管理制度，按海关要求建立帐册、记录投料与产出时间备查。
Secondly, the factory shall perfect its management system, and establish accounts, record material input and output for future reference as required by the customs.
本提升机的料斗为间断式布置，利用“掏取法”进行装载，“离心投料法”卸料。
The hoist hopper for layout, intermittent loading by determining the "tao", the "centrifugal feeding method" discharge.
结果：制备的阿霉素磁性明胶微球最佳投料比为1：15，磁吸附率为100%。
Results: The optimal ratio of magnetic gelatin microspheres carried adriamycin was 1:15. The magneto-adsorption rate of the microspheres was 100%.
投料试生产和性能测试的详细程序由卖方在完成试车前提出，最后由双方协商一致。
Detailed procedures for the Commissioning and Performance Test shall be submitted by the Seller before the completion of Test Runs and be agreed upon by both Parties.
采用正交实验，考察了原料投料比、回流反应时间、催化剂等因素对合成的影响。
The effects of feed composition, reflux reaction time and catalyst concentration on PPTD yield were investigated.
本文扼要介绍了自动投料机的工作原理、性能参数，重点介绍了电器控制技术和特点。
The paper briefly introducedd the work principle and performace parameter of automatic distributor for filling package and introduced mainly the technology and feature of the electronics control.
本文主要介绍了二次甲醛投料对脲醛树脂性能的影响以及提出选择生产工艺的最佳方案。
This paper mainly presents the effect of secondary adding formaldehyde on the properties of UF Resin and puts forward the best way to select the producing technology.
路面水泥混凝土通常是按砂、石、水泥、水一次投料的搅拌工艺制备的，其质量容易波动。
The pavement cement concrete is usually prepared by sand, stone, cement, water, feed mixing process, the quality fluctuates easily.
考察了酸醇投料摩尔比、混合液的进料流量、催化剂的填充密度等因素对反应过程的影响。
The influence of the factors, such as the molar ratio of acetic acid ton-butanol, the feed rate of the reactants and packing density of the catalyst, was investigated.
具备4大防错功能的先进的配投料防错系统能有效的避免橡胶材料的配合错误和投放错误。
Adopt advanced defensive system with 4 main anti-error function to avoid any mistake during batching and feeding.
实验结果表明，改变投料顺序、投料比以及三甲胺的投料方式有利于提高产品的收率及纯度。
The experiments proved that the changes of materials adding order, the ratio of raw materials and the loading way of trimethyl amine were advantageous to improve the yield and purity of the product.
在制备聚酯二醇的实验中主要研究了醇酸摩尔投料比和高真空时间等对合成分子量有影响的因素。
Influence factors, such as molar excess content of glycol, high vacuum time, are mainly studied in the synthesis of polyester glycol.
同时讨论了共聚物单体配比、PEG分子量、PEG与马来酸酐的投料比与酯化产物的性能关系。
The relationship between the factors such as the molecular weight of copolymer and PEG, the proportion of monomers and PEG, have been discussed.
同时讨论了共聚物单体配比、PEG分子量、PEG与马来酸酐的投料比与酯化产物的性能关系。
The relationship between the factors such as the molecular weight of copolymer and PEG, the proportion of monomers and PEG, have been discussed.
应用推荐