通过对数据接收电路CPLD内部参数的调整,可以实现对各种数字接口器件的配置,从而使得电路控制更加简单、灵活与可靠。
By adjusting parameters in CPLD of data receiving circuits, we can implement configuration of all kinds of digital interface devices, which makes the circuit control simpler, neater and more reliable.
并对超声波发射接收电路的硬件结构和工作原理做了较详细的说明,给出了数据处理系统程序框图和部分程序。
Explicated the structure and principle of work of ultrasonic launching and receiving circuit, presented the program frame and part program of the date processing.
译码电路接收测量端模拟信号,转化为7段显示的数字信号,发送到数据锁存器上。
The A/D decoding circuit received simulation signal form measurement port and converted the signals into data signals which displayed by 7-segment, then signals were sent to data latch.
详细阐述发送电路、接收通道电路、数据采集电路、万用表电路的设计。
It explicates design of transmitting circuit, receiving channel circuit, data acquisition circuit and multimeter circuit.
前端采集插头接收测试数据,切换继电器电路传递被测电路板信号。
Testing data is received with data acquisition plug, signal from tested circuit board is transferred by circuit of switch relay.
论文设计了光源发射驱动、光信号接收、信号调理及数据采集等硬件电路,以获得计算血氧饱和度所需的信号。
Light sources launch driven, light signal reception, signal conditioning, and data acquisition system were designed, and signals for calculating oxygen saturation were acquired by these circuits.
介绍了基于SJA1000的CAN总线接口电路的软硬件设计方法,给出了CAN总线接口电路、SJA1000初始化程序、接收及发送数据程序的框图。
This paper discusses the designing method of CAN bus juncture circuit based on SJA1000 and presents the CAN bus juncture circuit, the SJA1000 initialization programme and the flow charts.
数据电极驱动电路用以根据接收自主机的数据信号以及特定伽玛值信号来依序驱动数据电极。
The data pole driving circuit is used to drive data pole according to data signal from host computer and special gamma value signal.
发射机路径包括接收多通道二进制数据,并且为每个通道生成数据的数字表示的数字调制电路。
The transmitter path includes a digital modulation circuit receiving multiple channel binary data, and for each channel generating a digital representation of the data.
因此本文还详细阐述以下内容:硬件方面采用了高频窄脉冲信号发生及接收放大电路、高速数据采集电路;
On the aspect of hardware, they include: narrow pulse and high frequency ultrasonic sensor's design, high frequency signal generator and receiver's design, high speed data completed sampling's design.
第三,研究与实现了接收端的信号检测、信号放大、数据采集电路,测试表明电路功能良好。
Thirdly, the receiving-end consist of signal detection circuit, amplifier and data receiving circuit is also fabricated. Measuring results show that it performs well.
在一些实施例中,接收机锁存器电路包括动态锁存器,该动态锁存器具有至少一个用于接收输入数据信号的输入端子和至少一个锁存器端子。
In some embodiments, a receiver latch circuit, includes a dynamic latch having at least one input terminal to receive an input data signal and at least one latch terminal.
针对短时突发数据接收对位同步电路的要求,设计一种基于FPGA的硬件开环位同步电路。
A hardware electrocircuit scheme for bit synchronization are designed to met the demands of bit synchronization little paroxysmal data receiving in wireless digital system.
在发送端时钟频率随时间变化的情况下,以较低的成本和较简单的电路实现,保证了接收端采样数据及音频数据恢复的准确性。
Because clocking frequency of sending terminal is changed with times at lower cost and simple circuit, accuracy of receiving end sampled data and audio - data recovery is assured.
在接收器电路的设计中,论文采用了经优化的新型拓扑结构,提高了数据采样和接收精度;
The receiver circuits in the chip adopts novel optimized topology in order to increase the precision of sample, hold and process;
钳位电路用于某些数据设备可使接收器输出为常量,并且可在没有收到数据信号时避免噪音干扰。
A clamp is used in some data sets to hold receiver output constant and avoid troublesome noise interference when no data signals are being received.
钳位电路用于某些数据设备可使接收器输出为常量,并且可在没有收到数据信号时避免噪音干扰。
A clamp is used in some data sets to hold receiver output constant and avoid troublesome noise interference when no data signals are being received.
应用推荐