开发了一种超声电火花线切割复合加工装置。
A new kind of device has been developed, by which hybrid technology of ultrasonic and WEDM is performed.
慢走丝电火花线切割加工精度是衡量加工性能的重要指标之一。
Machining accuracy of slow-feeding EDM wire-cut is one of major targets scaling processing properties.
电火花线切割加工的表面粗糙度是衡量加工质量的重要指标之一。
The surface roughness in the wire cut of electric discharge machine work is one of the important parameters to measure the work performance.
开发了能实现复杂曲面零件电火花线切割加工的多轴联动加工系统。
In this paper, the motion rules of multiple spindle linkage motion in machining complex ruled curved surfaces by WEDM was analyzed.
研究了电火花线切割加工工程陶瓷的表面完整性及其淬火强化处理。
This paper attempts to study the surface integrity of WEDM engineering ceramics and their strengthening by quenching.
主要介绍了当前慢走丝电火花线切割脉冲电源的研究现状和新的发展趋势。
The paper introduces the research status and the new trend in development of pulse generator for LSWEDM.
分析了板线内导体在利用数控电火花线切割加工中所遇到的工艺技术难题。
The core technique problems during wire cut electrical discharge machining in the inner conductor sheet were analyzed by this paper.
本文进行了电加工中的磁力电解抛光和干式电火花线切割两方面内容的研究。
WE study two areas of the electro-machining: the magnetic force electrolysis polishing and the dry-type WEDM.
用光学显微镜观测和分析电火花线切割硅表面沿纵向分层择优腐蚀后的形貌;
The surface morphology after preferential corrosion along the vertical orientation was observed via an optical microscope.
气中电火花线切割加工技术是近几年出现的一种新技术,它采用气体作为介质。
WEDM in gas is a kind of newly developed technology, in which gas has been used as a dielectric.
高速走丝电火花线切割加工过程中,电极丝有时会出现先有花斑后断丝的现象。
Indistinct pattern are sometimes found on the wire electrode wound regularly in reciprocating travelling WEDM.
高速走丝电火花线切割加工过程中,电极丝有时会出现先有花斑后断丝的现象。
Indistinct pattern are sometimes found on the wire electrode wound regularly in reciprocating travelling WEDM. It is appeared before wire broken.
研究了在大气和乳化液两种介质中,峰值电流对高速走丝电火花线切割加工的影响。
The influence of peak current on finishing high-speed wire electrical discharge machining (WEDM) in gas and emulsion dielectric is studied.
探讨在电火花线切割得到广泛应用的背景下,电火花线切割数控编程的手段和方法。
The article discusses the means and method of numerical control programming under the background that spark erosion wire cutting is applied extensively.
电火花线切割加工精度,主要指尺寸精度、形状精度、位置精度以及加工表面粗糙度。
The machining accuracy of WEDM means mainly the dimensional accuracy, accuracy of form, accuracy of position, and the surface roughness of cut surfaces.
在现代电力电子技术基础上,开发出新型微能可控的微细电火花线切割加工脉冲电源。
Base on power electronic, a newly micro energy controlled pulse generator for MWEDM was developed.
电火花线切割加工过程复杂多变,难以定量控制,影响因素较多,相互关联又相互矛盾。
Wire Electrical Discharge Machining (WEDM) process is changeable and difficult to control quantitatively. Many factors influence the process and they are related and contradictive.
开发了以新型翻转式自动分度数控回转工作台为核心的复杂曲面电火花线切割加工系统。
Taking newtype numerical control turntable as the core, a WEDM system for complicated surfaces was developed.
应当对高速走丝电火花线切割的各个方面综合治理,才能在提高加工精度上取得突破性成果。
Only by tackling the problems concerning various aspects in a comprehensive way can we gain the breakthrough in raising the machining accuracy of WEDM with high wire-travelling speed.
以混凝土拖泵中的典型零件——摇臂为例,介绍数控电火花线切割在内花键孔加工中的应用。
Taking the rocker arm of trailer concrete pump as a typical example, application of nc electric-spark line-cutting to female spline machining is described.
采用一般的脉冲电源对磁钢进行电火花线切割加工,不可避免地将引起充磁,造成排屑困难。
When the method of general pulse power of wire cut EDM is used, magnetic steel has magnetic property inevitably and it is difficult to evacuate.
对进一步提高微细电火花线切割加工精度,减少电极丝的损耗,降低加工成本具有一定意义。
The measures and solution for decreasing wire wear are proposed, which are significant to increase the precision of Micro-WEDM process, reduce the wire wear and cost of the machining process.
设计了一套超声辅助电火花线切割加工的实验装置,并对复合加工的机理和特性进行了研究和探讨。
A set of experimental device that ultrasonic aided wire cut machining has been developed. and the mechanism and inherent nature of combined technology are explored and studied in deep going.
因此,本论文从实际工程应用的角度来开发低速走丝电火花线切割微机编程软件,是具有现实意义的。
So, from the point of practical engineering application, it is of great realistic significance for this theme to develop software for computer programming of wire electrical discharge machining.
电火花线切割加工时工具(电极丝)和工件之间的放电电压是对放电加工过程进行实时检测的重要参数。
Voltage between tool and workpiece is an important parameter in the on line monitoring of wire electrical discharge machining (WEDM) process.
电火花线切割非直线和非圆弧的模具刃口前,需先用圆弧拟合模具刃口曲线,以便计算线切割编程数据。
Before EDM wire cutting die points of non_straight and non_arc lines, an arc for fitting the curve of the die point is necessary so as to calculate wire_cutting programming data.
本文采用传统方法进行电火花线切割加工工艺参数优化,分别建立了加工速度和表面粗糙度的数学模型。
This article is about the processing parameter optimization achieved through the traditional method to set a mathematical model of the processing speed and surface roughness.
试验表明,这种高质量的脉冲电源为改善微细电火花线切割加工整体性能、拓展加工领域提供了技术保证。
A large quantity of experiment show that this MWEDM pulse generator can improve overall process performances, provide guarantee of technology for expanding machining field.
试验表明,这种高质量的脉冲电源为改善微细电火花线切割加工整体性能、拓展加工领域提供了技术保证。
A large quantity of experiment show that this MWEDM pulse generator can improve overall process performances, provide guarantee of technology for expanding machining field.
应用推荐