Strength Design values may be converted to Allowable Stress Design values.
设计要求、强度设计值可转换为许用应力设计值。
Some datum, for example safety factor and allowable stress are put forward based on production practice.
提出的设计数据如安全系数、许用应力均根据生产实践的应用所确定。
In this case allowable stress of imported material shall be those for equivalent material in GB150-1998 as follows.
在此情况下，进口材料的允许应力与GB150- 1998中的相当材料相同。
The allowable stress is the value of the determined basic allowable stress of the piping material multiplied by a quality factor.
而管道许用应力是在确定了管道材料的基本许用应力后，乘以质量系数所得的值。
The allowable stress levels to which the actual stress levels are compared are based on empirical findings for the material involved.
对所使用的材料来说，与实际应力比较的容许应力是以实验研究结果为基础的。
The allowable stress of the pipe material shall be chosen from the data of GB 50316 Design Specification for Industrial Metal Piping.
管子材料的许用应力可按GB 50316《工业金属管道设计规范》中的数据选用。
At last, under the allowable stress with ANSYS to optimize the design of the final model and gain a new kind of horn with resonance of 12.35.
最后借助ANSYS优化设计模块进行仿真实验，在材料许用应力下对变幅杆进行优化设计，获得了谐振比达12.35的新型变幅杆。
If the above link is greater than the allowable stress, it will lead to destructive damage, or even crack, collapse and other serious consequences.
以上环节中若出现大于允许应力时，就会导致破坏性损伤，甚至折裂、坍塌等严重后果。
The many indefinite exists in the design parameters and influence factors of the working stress and allowable stress of the roller movable teeth drive.
滚子活齿传动设计中，在工作应力、许用应力的设计参数和影响因素中存在着许多不确定性。
According with the allowable stress design theory, the wind loads and load-carrying capacity of antenna struts are calculated, and their inter forces are analyzed.
根据容许应力设计理论，对天线撑杆的风荷载和承载能力进行结构计算，并对天线撑杆进行内力分析。
Bridges of this kind are designed according to fully prestressed concrete theory, and tensile stress is allowed to exceed allowable stress during construction and service.
这类桥梁在设计计算过程中均是按照全预应力混凝土结构进行设计的，施工和运营中任何截面混凝土拉应力均不允许超过允许应力值。
The results indicate that it is conservative to design CFST arch Bridges by using allowable stress method in steel tube, and that it is reasonable to use limit state method.
数例表明，目前广泛应用钢管应力控制CFST的设计过于保守，文中方法似更合理。
Then, suggested values of the allowable stress ranges corresponding to different target fatigue lives under the specified ensuring probability were proposed for corroded steel bars.
经统计回归，建立了考虑锈蚀率影响的锈蚀钢筋疲劳曲线方程，给出了不同保证率、不同预期疲劳寿命下自然锈蚀钢筋容许应力范围的建议值。
Selection basis and method on allowable contact stress of rolling ball-socket nozzle were described. Based on empirical formula and test data, several factors affecting allowable stress were analyzed.
叙述了滚动球窝喷管在设计中许用接触应力的选择依据及方法，并根据以往的经验公式及其试验数据对影响许用接触应力的几个因素进行了分析。
The primary cause of breakage is that the dynamic stress exceeded the allowable fatigue limit of the beam, and another cause is that the structure of the beam is unreasonable.
通过计算证明引起断裂的根本原因是动应力超过了梁的许用疲劳极限，另一原因是梁的结构不合理。
The proposed formula used to evaluate the allowed fatigue stress range shows that a new amendment for the criterion of allowable fatigue stress provided in the current code is necessary.
提供的公式可用来估定合乎实用的疲劳应力幅值，表明现行规程中提供的疲劳容许应力指标需要加以修正。
Through analysis, we consider that the spiral case of left powerhouse units works normally, and that the stress and deformation are within the range of allowable design.
通过分析认为左厂房机组蜗壳工作性态正常，应力和变形均在设计允许范围内。
If the design is based on the strain hardened properties, the allowable design stress will usually be above the actual yield point of the HAZ.
如该设计基于应变硬化性能，设计应力通常在HAZ实际屈服点以上。
Axis press allowable bending stress calculation method trunnion check.
轴按许用弯曲应力计算法校核轴径。
The new formula for computing the allowable tensile stress given in the new specifications is not reasonable.
该规范提出了一个混凝土允许拉应力计算公式，这个公式不宜采用；
There will be a certain thermal stress in the lining during operation, but the stress is not great, being only about one tenth of the allowable tensile stress of the reinforcing bars.
隧洞衬砌运行时具有一定的温度应力，但其值不大，仅为钢筋允许拉应力的十分之一左右。
These formulas more actually reflect the strength characteristics of massive concrete and visually show allowable design stress of concrete under certain operation state.
公式较真实地反映了大体积混凝土的强度特性，直观地表明了在某运行状态下混凝土可容许承受的应力。
Reasonable date and equations for allowable shearing stress are proposed.
以公式化的形式给出了许用剪应力的更合理的数值。
Reasonable date and equations for allowable shearing stress are proposed.
以公式化的形式给出了许用剪应力的更合理的数值。
应用推荐