This paper simulates the temperature field associated with laser surface quenching using ANSYS - a finite element analysis software, and a series of studies are carried out based on this simulation.
本文结合先进的大型有限元分析软件ANSYS，对激光表面淬火的温度场进行有限元模拟，并在此基础上，对此展开一系列研究。
Three-dimensional flow simulation of flight element in mixing zone of a conical twin-screw is performed with a finite element package, ANSYS.
用ANSYS有限元分析软件对锥形双螺杆螺纹元件流道的流场进行了三维模拟。
In order to solve the eccentric worn problem of tubing, deformation finite element simulation of the eccentric worn tubing was carried out with ANSYS software under internal pressure and axial load.
为了解决油管偏磨问题，对内压和轴力作用下的无偏磨、单面偏磨和双面偏磨油管分别进行了有限元(AN - SYS软件)模拟研究。
The numerical simulation and analysis of shear resistance behavior of two-side connected steel-plate shear wall (SPSW) was carried out by the finite element software ANSYS.
采用ANSYS有限元程序对两边连接钢板剪力墙进行数值模拟分析。
Three-dimensional flow simulation of mixing zones in a new conical twin screw extruder with mixing blocks is performed with a finite element package, ANSYS.
利用ANSYS有限元分析软件对带有混合块的新型锥形双螺杆的混合段流场进行了三维模拟分析。
A numerical simulation program for flexural load effects of rc beams was compiled based on the theory of reinforced concrete and finite element software ANSYS.
根据钢筋混凝土理论和ANSYS有限元软件编制了实验梁受弯荷载效应模拟计算程序。
The finite element numerical simulation for the triaxial compression tests also had been carried out using the commercial software ANSYS.
并利用ANSYS软件考虑筋、土的相互作用对三轴试验进行了数值模拟计算。
Numerical simulation of finite element method for pile-bucket foundation under uplifting load were conducted by making use of ANSYS software.
通过使用ANSYS软件，对桩-桶基础上拔试验进行有限元数值模拟。
Therefore, based on rolling bearing implicit finite element solution analysis, using ANSYS/LS-DYNA explicit dynamic module implements, we achieved the rolling contact simulation of motion process.
因此本文在对滚动轴承有限元隐式求解分析的基础上，利用ANSYS/LS-DYNA模块对滚动轴承进行了显式动力学接触分析。
The parametric finite element model of the television with packaging structure was established and its dropping simulation was achieved using the finite element analysis software ANSYS/LS-DYNA.
利用有限元分析软件ANSYS/LS-DYNA，建立长虹电视带包装的参数化有限元模型，对电视裸机与带包装两种工况下的跌落仿真模拟和跌落实验；
The main work of this thesis is simulation of the thermal characteristic and cold-test characteristic for coupled-cavity TWT slow-wave structure with ANSYS, which is a finite-element software.
本文的主要工作就是利用大型通用有限元计算软件ANSYS模拟耦合腔行波管慢波结构的热特性和冷测特性并对该软件进行了二次开发。
ANSYS software simulation of the arch tunnel excavation and support structures of the finite element method were researched.
对ANSYS软件模拟连拱隧道开挖及支护结构的有限元理论进行了研究。
Study method is to adopt ANSYS-international large-scale general-purpose finite element software to realize the simulation calculation of the RCC thermal stress for Aggregate linear expansion.
在研究方法上采用国际大型通用有限元软件ANSYS建模来实现混凝土骨料线膨胀对碾压混凝土温度应力的仿真计算。
A comprehension simulation to the three dimensional flow field and temperature field in the mould of slab continuous casting was performed with finite element software ANSYS.
利用有限元软件A NSYS模拟计算板坯结晶器内三维流场和温度场。
With the same parameters, the numerical solution is in good agreement with the finite-element (ANSYS software) simulation.
在同样的参数情况下，用ANSYS模拟的结果和数值计算的结果吻合的较好。
The 3d finite element numerical dynamic simulation of welding between hollow ball and pipe was carried out based on ANSYS.
利用大型有限元分析软件ANSYS，对空心球与钢管焊接件的温度场和应力应变场进行了三维数值动态模拟。
The 3d finite element numerical dynamic simulation of welding between hollow ball and pipe was carried out based on ANSYS.
利用大型有限元分析软件ANSYS，对空心球与钢管焊接件的温度场和应力应变场进行了三维数值动态模拟。
应用推荐