Master cylinder bushing at the clutch pedal.
离合器踏板处的总泵衬套。
The transformer shall employ pure porcelain bushing.
变压器采用纯瓷套管。
The cast iron rod bushing provides maximum load bearing support.
铸铁连杆衬套提供最大承重的支持。
Align adapter bushing or gear operator (3) bore with valve stem (5).
用阀门的阀杆(5)对准适配器衬套或持论操作机构(3)镗孔。
All bus and the ramus bus are covered with pyrocondensation bushing.
所有母线和分支母线都用热缩套管覆盖。
The extra long bushing offers excellent load bearing characteristics.
额外的长期套管提供出色的承载特性。
Bushing is one of the most important insulation parts in transformer.
套管是变压器中一种重要的部件。
The longer bronze rod bushing provides a maximum load bearing support.
时间越长青铜连杆衬套提供最大承重的支持。
Tighten leaf spring press until bushing is extracted from leaf spring.
上紧叶片弹簧加压机直到衬套被拔出叶片弹簧。
The longer cast iron rod bushing provides maximum load bearing support.
铸铁的时间越长连杆衬套提供最大承重的支持。
The function of a bushing is to prevent metals from touching one another.
衬套的作用是阻止金属的彼此碰撞。
Place Taper - lock Bushing and Timing Belt Pulley on the transmission shaft.
将锥面紧固套与同步带轮装在传动轮上。
Self-lubricating rod bushing with a low coefficient of friction for smooth actuation.
自润滑连杆衬套的低摩擦系数平稳驱动。
In this, can use repair drive shaft and bushing method to recover its normal fit clearance.
遇此，可采用修主动轴或衬套的方法恢复其正常的配合间隙。
That way, all movement takes place between the bushing and bearing - instead of on the bolt.
这样，所有运动的发生之间的衬套和轴承-而不是对螺栓。
In this experiment, the flame stability under large bushing is better than under small bushing.
在实验中，大套管实验工况的火焰稳定性比小套管要好。
The steel retaining plate has two functions, retaining the bushing and preventing rod rotation.
固定板的钢具有两种功能，保留套管和防止杆旋转。
Connection of lead and bushing shall be tight and correct, bushing should be in good condition.
引出线与套管的连接应牢靠，接线正确。套管应完好无损。
The bushing ring flange suitable temperature is decided by the designer according to the situation.
衬环法兰的适用温度由设计者根据情况决定。
Taper ceramic bushing for spindle is developed for machining center, so that the performance is improved.
针对加工中心研制了主轴锥孔陶瓷衬套，使机床的性能得到改善。
The designer may lower the pressure on the packing by placing a throat bushing in the pump case (Figure).
设计者可在泵壳内放置喉道补心以降低在填料上的压力(图)。
The extra wide wear band is located at the furthest point from the rod bushing to support maximum loading.
穿的超宽频段位于从套管支持最大负荷杆最远点。
The new full-enclosed explosion-resistant oil-paper capacitor bushing and its characteristics are introduced.
介绍了一种新型全密封阻爆式油纸电容套管及其性能和特点。
The correctness of this algorithm is verified by the processing results of on-site data of transformer bushing.
对变压器套管现场数据的处理结果验证了该算法的正确性。
Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.
曲轴上的导向轴承：曲轴上的导向轴承一般或者是轴瓦，或者是球轴承。
Through development and on-board test of ZA alloy bushing, its wearing performance has been further demonstrated.
通过ZA系列锌铝合金轴套的研制和装机试验，进一步证明其耐磨性能。
The kelly bushing (KB) has an inside diameter profile that matches that of the kelly, usually square or hexagonal.
方钻杆补心的内径通常与方钻杆的外径（通常是四方钻杆或六方钻杆）相匹配。
Depth measurements are commonly referenced to the KB, such as 8327 ft KB, meaning 8327 feet below the kelly bushing.
井深测量通常是指方钻杆补心高度，如补心高度8327英尺，就意味着在方钻杆补心以下有8327英尺的深度。
Notably no varus collapse due to bushing failure was noted despite a high percentage of high-energy unstable injuries.
值得注意的是没有发现一例因套管失效而导致的内翻塌陷，尽管高能量不稳定性损伤占有很高比例。
Notably no varus collapse due to bushing failure was noted despite a high percentage of high-energy unstable injuries.
值得注意的是没有发现一例因套管失效而导致的内翻塌陷，尽管高能量不稳定性损伤占有很高比例。
应用推荐