The error depends on the calibration accuracy of the amplitude response.
这种方法的误差取决于幅频特性曲线的标定精度。
Testing results using real data show that it improves calibration accuracy.
数据实验表明：标定精度比直接采用分步法有所提高。
The calibration accuracy is less than 0.5 pixel, which conforms to requirements.
本次校正精度小于0.5个像元，符合要求。
When the radius of the control space within 4.5 meters, the calibration accuracy has reduces;
被标定范围的半径在4.5米以内时，标定精度有所降低；
Calibration accuracy is guaranteed to the tips of the HP 41941a (1.5 m) and HP 41941b (3 m) impedance probes.
校准精度，是保证向两端惠普41941a (1.5m)和惠普41941b(3米)阻抗探头。
An analysis of factors influencing the calibration accuracy is done based on the experimental process and results.
根据试验的过程和结果，分析了影响标定精度的因素。
The accuracy of vision measurement system is influenced by choices of the calibration method and calibration accuracy.
摄像机标定方法的选择和标定精度直接影响着轮对动态视觉测量系统的精度。
A new method ameliorating the calibration accuracy for flowmeter that is based on BP network - (genetic) algorithms (GA) is proposed.
提出一种基于神经网络(BP)-遗传算法(GA)的高精度流量仪表标定方法。
When the satellite geometry is good, the rubidium clock is used to improve vertical accuracy, and in turn, the calibration accuracy of the barometer.
当卫星几何位置好的情况下，铷钟用于改善垂直精度，顺便还较正气压计的精度。
Generally, the minute and complicated instrument calibration procedure and inefficient management give rise to frequent problems in calibration accuracy.
通常的仪表检定过程较繁琐，且管理上无法保证检定人员的工作质量，因此现场仪表的检定精度很容易出现问题。
The actual accuracy is due to the calibration accuracy. Calibration methods affect the convenience and dependability of an optical measurement system directly.
系统的标定精度直接决定了系统的实际使用精度，而标定方法又直接影响着视觉测量系统的使用方便性和可靠性。
This paper discusses the dependence of the absolute calibration accuracy on the characteristics of the switch used in the equipment for calibrating calorimeters.
本文讨论了激光能量计绝对定标装置中所采用的开关特性对定标精度的影响。
The system implements remote control and improves calibration accuracy, efficiency and security. The result of thrust calibration in normal temperature attains 0.05%.
该系统实现推力校准的远距离控制，提高校准精度、效率和安全性，常温校准结果可达到0.05%。
Using this method, we can obtain higher calibration accuracy than using Gauss least-square method when calibrating close range, which is very practical in engineering.
该方法的近距离标定精度比高斯最小二乘法高，具有工程实用意义。
Correcting the distorted image of camera in calibration process of fringe projection measurement system that can effectively improve the calibration accuracy of system.
在条纹投射测量系统的标定过程中对摄像机畸变图像进行修正，能有效地提高系统的标定精度。
The actual accuracy of an optical measurement system is due to the calibration accuracy. The calibration methods should possess the property of convenience and dependability.
线结构光的标定精度直接决定了测量系统的实际测量精度，而标定方法又直接影响着测量系统使用的方便性和可靠性。
Simulation and test results of a laser gyro strapdown inertial navigation system show that the improved calibration scheme can increase the calibration accuracy and improve the navigation performance.
仿真和试验对标定编排改进前后的标定精度和导航性能进行了对比，表明改进编排方案可以提高陀螺和加速度计安装误差角标定精度，改善系统导航性能。
Second, device after calibration of pressure gauge, to check the accuracy of the work pressure gauge.
二是装置经过校验的压力表，以便核对工作压力表的准确度。
Responsible for site instrument management, including procedure establishing, calibration management, to ensure its accuracy and compliance with regulation of local and corporation.
负责工厂的仪表校正管理，包括制定相关程序，日常校验管理，确保其精确度并符合国家和公司的规定。
Since the ultimate measuring accuracy is limited by the accuracy of calibration, a new method of calibration is proposed in this paper.
由于测量的精度最终要受到标定精度的限制，本文引入了一种新的标定方法。
The accuracy grade of novel HVEM must be defined by integrated error calibration system.
新型高压电能表必须采用整体误差校验系统来定义准确度等级。
Experimental results show that the proposed method has a quite high accuracy of calibration.
实验结果表明，所提方法具有较高的定标精度。
Swing shaft test bench is used to test alignment, calibration and accuracy of system under simulating swing condition in laboratory.
摇晃轴试验台是在实验室模拟摇晃条件下，对被试系统进行对准、标校及精度试验的一种装置。
Software calibration method is used to increase measuring accuracy and reliability.
采用软件校正，提高了测量精度和整机的可靠性。
In dynamic structure testing, the accuracy of measurement data relies significantly on the calibration quality of measurement channels.
在结构动力学试验中，测量通道的校准质量直接影响测量数据的精度。
As a basic guarantee of thermal instrumentation accuracy, thermal instrumentation calibration quality has an important impact on production safety.
作为热工仪表准确性的基础保障，热工仪表的校验质量对生产安全有着重要的影响。
By offline calibration for the coordinate measurements device, the measurement accuracy is promoted.
通过对坐标测量装置的离线刻度，提高了测量精度。
Use amplifiers, receivers must consider the level and burned compression level to take appropriate measures calibration, in order to improve measurement accuracy of the system.
采用放大器，就必须考虑接收机的烧毁电平和压缩电平，采取适当的措施进行校准，以便提高系统测量准确度。
Use amplifiers, receivers must consider the level and burned compression level to take appropriate measures calibration, in order to improve measurement accuracy of the system.
采用放大器，就必须考虑接收机的烧毁电平和压缩电平，采取适当的措施进行校准，以便提高系统测量准确度。
应用推荐