Technology characteristics of cold rolled sheet unit of Benxi Steel Posco Cold Rolled Co. , Ltd. ;
介绍了莱钢冷轧薄板（一期）工程的主要生产工艺、设备配置及先进技术。
Technology and installations for the production of cold rolled sheet at PZH Steel were introduced.
对生产中常见的低碳铝镇静钢冷轧板孔洞缺陷特征进行了宏观和微观分析。
Tinned sheet is cold rolled sheet whose surface is electroplated with a layer of uniform and dense tin.
镀锡板就是在冷轧板的表面电镀一层均匀致密的锡层。
High cleanliness is required for low carbon aluminum killed (LCAK for short) steel which is widely used for production of cold rolled sheet.
低碳铝镇静钢(LCAK)常用于生产冷轧板，要求铸坯有高的洁净度。
These housings (series p) are produced from cold rolled sheet steel and are protected against corrosion by a yellow chromate surface treatment.
这些轴承座(系列p)用冷轧钢板制造，表面经过黄色镀铬处理，以防腐蚀。
Porosity cluster of cold rolled sheet is transformed from scars, and it is critical to avoid collision for improving the surface quality of hot rolled strip.
避免钢板撞击精轧机组侧导板是消除结疤缺陷提高热轧板材质量关键因素之一。
Coil Packaging is a very important auxiliary process of the cold rolled sheet production. China has been falling behind developed-country in this technology.
钢卷包装是冷轧生产中很重要的辅助工艺技术，我国在这一技术上与世界工业发达国家相比落后很多。
The strip winding near the inner core of coil car has always been stripped while discharging coil since galvanizing mills put into operation in Angang Cold Rolled Sheet Plant.
鞍钢冷轧厂镀锌机组自投产以来，一直存在钢卷车在卸卷时发生内径抽芯卸卷失败等卸卷故障。
The difference of phosphate coating between aluminum alloy sheet and cold rolled sheet is compared by the test of chemical converted film and its structure on the surface of aluminum alloy sheet.
通过对铝合金板材进行的化学转化膜及膜结构的研究试验，对比了铝合金板与冷轧钢板磷化的异同点。
The mass concrete construction method for the equipment foundation in BX steel POSCO cold rolled sheet plant and technical measures for controlling its crack development were introduced in this paper.
介绍了本钢浦项冷轧薄板厂大体积混凝土设备基础的施工方法，以及控制其裂缝开展的技术措施。
Capacitor shell adopts the high quality cold-rolled steel sheet or stainless steel sheet, and with mounting bracket for lifting on both sides which equipped with special grounding screw.
电容器外壳的材质采用优质冷轧钢板或不锈钢板，两侧装有供吊运安装支架，并装有专用的接地螺丝。
Process of rolling cold coils of pickled hot-rolled sheet through a cold reduction mill to make the stainless steel stronger, thinner, and smoother by applying pressure.
通过冷轧工厂轧制热轧的、酸洗的不锈钢薄板使不锈钢在压力作用下更薄、强度更高、更光滑。
In sheet strips production, the requirement of glancing flatness for cold - rolled sheets i. e. automobile body sheet, tinned steel sheet, silicon steel sheet and aluminium sheet is higher.
在板带生产中，对汽车钢板、镀锡钢板、硅钢板以及航空铝板等冷轧薄板的平直度有很高的要求。
The paper reviews the application of cold-rolled, hot-rolled steel sheet and round steels in the cab and chassis of domestic heavy truck, and discusses the methods to reduce automotive dead weight.
综述了国内重型汽车驾驶室和底盘用量较大的钢材——冷轧钢板、热轧钢板和圆钢在重型汽车上的应用现状，讨论和分析了降低汽车自重的途径和方法。
The effect of annealing temperature on fibrous texture of cold rolled IF steel sheet rolled from strip hot rolled in ferrite region was investigated.
研究了铁素体区热轧if钢经冷轧后，不同退火温度对丝织构的影响。
The major work in the paper is the transform of the pickle curve-centering device of the Baosteel cold-rolled sheet-steel rolling mill.
论文对宝山钢铁股份有限公司冷轧薄板厂的酸洗弧形对中装置进行改造。
The main production process, equipments collocation and advanced technologies of the primary cold-rolled sheet project are introduced in this paper.
介绍了莱钢冷轧薄板(一期)工程的主要生产工艺、设备配置及先进技术。
The effect of speed ratio on the texture of non-oriented cold rolled low silicon steel sheet was investigated after cross shear rolling at different speed ratios.
选取低硅无取向硅钢常化态板材，分别在不同速比下进行异步轧制，考察了速比对低硅无取向硅钢冷轧织构的影响。
The production capacity of hot rolled wide strip has already meet the need in China, even maybe overplus. The transfer rate of hot rolled wide strip into cold rolled one and coated sheet is small.
指出我国热轧宽带钢生产能力已能满足国内需求，并可能出现过剩，但转化为冷轧板带和涂镀层板比例太低。
The paper introduced the equipment, technology innovation and application situation of the domestic large-scale and high speed continuous annealing line for cold rolled silicon-steel sheet.
介绍了我国设计建设的大型高速冷轧硅钢片连续退火机组工艺及设备装备水平，技术创新及应用情况。
A method of analysing the gauge tolerance standards of cold-rolled steel sheet was put forward.
提出了一种对冷轧薄钢板厚度公差标准水平进行分析比较的方法。
Cold-rolled plate, galvanized sheet, hot-rolled plate, iron ore, pickling board, processing, steel, surface treatment, Pipe, 5600 yuan per ton.
冷轧板，镀锌板，热轧板，铁矿石，酸洗板，加工，钢铁企业，外表处置，钢管，每吨5600元。
Series Y3 asynchronous motors is a new series of general purpose low voltage three-phase cage motors designed with cold-rolled silicon steel sheet.
Y 3系列异步电动机是采用冷轧硅钢片作为导磁材料而设计的一般用途低压三相笼型异步电动机基本系列。
The characteristics and forming reason of faint-sliver defect found in cold-rolled steel sheet were discussed.
对冷轧板中发现的条痕缺陷特征进行了分析，探讨了该缺陷的形成原因。
The forming properties of SPCD and SPCE cold-rolled sheet are tested and compared through experiments such as drawing, macrostructure and FLD.
通过拉伸、宏观织构、FLD等实验，测试并比较了SPCD和SPCE冷轧板的成形性能。
Based on analysis and study, this paper advances Suggestions and solutions to the problem about iron loss increasing of punched cold-rolled non-oriented silicon steel sheet after heat treatment.
针对冷轧无取向硅钢冲片在热处理后铁损值升高的问题进行了分析研究，并提出了解决措施和建议。
Based on analysis and study, this paper advances Suggestions and solutions to the problem about iron loss increasing of punched cold-rolled non-oriented silicon steel sheet after heat treatment.
针对冷轧无取向硅钢冲片在热处理后铁损值升高的问题进行了分析研究，并提出了解决措施和建议。
应用推荐