The test results indicate that both the tensile stress and the contact pressure affect the FFL.
结果表明拉应力和法向压力均影响微动疲劳寿命。
Fuji pressure-sensitive film was used to record the contact pressure and area for each testing condition.
使用富士压力感应胶片记录接触应力和每个检测条件区域。
The calculated results indicate that the axial distributions of the maximum contact pressure have an "s" shape.
结果表明，最大压应力轴向分布呈S形，原辊形会引起接触应力集中。
Pressure the General Assembly to premature seal failure, and the contact pressure is too small will cause leakage.
压力过大会促使密封过早失效，而接触压力过小则会引起泄漏。
The effects of contact pressure, internal energy and damage dissipation energy on the impact response were analyzed.
分析了接触力、加筋壁板吸收能量和损伤散逸能对冲击响应的影响。
In the default model the friction coefficient is defined as afunction of the equivalent slip rate and contact pressure.
在默认模型里，定义摩擦系数为等效滑移率和接触压力的函数。
The technique of directly measuring the contact pressure was employed and the method compared with the indirect method.
该方法是采取直接测量接触压力分布技术，并与间接测试方法进行了比较。
Operating weight and ground contact pressure can be adjusted by filling water or wet sand with greater adjusting scope.
通过加水或湿沙可调节压路机配重和接地比压，调节方便范围大；
The distributions and changes of the contact pressure, flow stress and velocity field on the welding plane were analyzed.
分析了不同分流模模桥结构下焊合面上接触压力、流变应力和速度场的分布及其变化。
The contact pressure of the side cleaning brush during cleaning can be controlled by the tested reliable equilibrium technology.
侧面清洗刷清洗过程中的接触压力经过测试的可靠的均衡技术来控制。
Vertical and annular reinforcing steel bar stress and pipe-soil contact pressure during pipe jacking were monitored on the spot.
对顶进过程中管道纵向与环向钢筋应力及管土接触压力进行了现场测试。
The sweeper installation, adjustment and the contact pressure should comply with the requirements of the specification of factory.
清扫器的安装、调整及接触压力等应符合厂家说明书的要求。
The change rule of the contact pressure, nucleation process and character were investigated by the coupled thermal-electrical-mechanical analysis.
通过结构、热电场的全耦合，分析了焊接过程中接触面压力变化规律，单边焊熔核形成过程以及形核特点等。
The electrode-to-workpiece and workpiece-to-workpiece con tact behaviors are analyzed, and reasons for contact pressure distribution are explained.
通过数值模拟发现，电极压力和电极球面半径是影响电极-工件间接触面大小的主要因素；
An adjustable force applicator supplies contact pressure to the contactor to apply a substantially constant force over a large working travel range.
可调节力施加器向所述接触器供应接触压力以在大的工作行进范围内施加大致恒定的力。
The roll separating force, rolling torque and contact pressure along the surface of the rolls are also evaluated by means of the finite element method.
轧制分离力、轧制力矩以及沿轧辊表面的接触压力也通过有限元法进行评估。
A simple and practical method was proposed to simulate the contact region and the contact pressure between the prestressed tendon and the wall of ropeway.
根据试验观察，提出了一种模拟预应力钢索与索道孔壁接触区域和接触压力的简单、实用的方法。
Taking an arch foot as an example, a practical met hod was proposed to simulate the contact pressure of the prestressed tendon according to the experiment.
以桥梁拱脚为例，依据实验结果提出了一种模拟预应力钢索与索道壁之间接触压力等代荷载的实用的方法。
According to the working principle of effective stress, the constitutive relation between dynamic water pressure and rock contact pressure has been analyzed.
根据岩土有效应力作用原理，分析了动水压力和岩体接触压力间的本构关系。
According to the deflection coordination condition of shell, the distribution rule of contact angle and the contact pressure between shell and tyre are obtained.
根据滚圈处筒体的变形及平衡条件，得出了筒体—滚圈的接触角及筒体—滚圈的接触压力分布规律。
The influence of the bite, the entrance and exit elastic deformation and the roller both ends contact pressure is considered. The formula is convenient and precise.
本公式考虑铝箔入口和出口弹性变形和轧制铝箔两侧轧辊辊身端部弹性接触压力对轧制力的影响。本公式计算精确而且简便。
Stranded conductors shall not be consolidated by soldering where they are subjected to contact pressure, unless the contact pressure is provided by spring terminals.
多股导线在其承受接触压力之处，不应使用钎焊将其焊在一起，除非由弹簧接线端子提供接触压力。
The goal of this study was to determine the effects of posterior root tears of the medial meniscus and their repairs on tibiofemoral joint contact pressure and kinematics.
本研究旨在确定内侧半月板后角撕裂的生物力学特性，以及修复后对胫股关节接触压力和动力学的影响。
Conductors of supply cords shall not be consolidated by soldering where they are subjected to contact pressure, unless the contact pressure is provided by spring terminals.
电源线的导线在其承受接触压力之处，不应使用钎焊将其合股加固，接触压力由弹簧接线端子提供。
Particle penetrating direction has influences on the magnitude of surface deformation, contact pressure and stress, and the distribution forms of contact pressure and stress.
磨粒侵入方向不仅影响材料表面变形、表面接触压力和表层应力的大小，而且会引起压力和应力分布形状的改变。
Based on production conditions and data, this article discusses the varying contact length back-up roll deformation under the condition of equal contact pressure between rolls.
以某中板厂生产条件和数据为基础，讨论了变接触长度支承辊辊间接触压力相等时的轧辊变形情况。
Based on production conditions and data, this article discusses the varying contact length back-up roll deformation under the condition of equal contact pressure between rolls.
以某中板厂生产条件和数据为基础，讨论了变接触长度支承辊辊间接触压力相等时的轧辊变形情况。
应用推荐