Install cross member and diagonal braces.
安装横梁和对角撑杆。
Loosen trailing arm on front-axle cross member and pull out of the mount.
松开前轴横梁上的拖臂并从支座中拔出。
Situate the steering knuckle assembly so that it fits on to the cross member knuckle back plate.
位于该转向节大会,以便它适合于板的横梁关节回来。
The tractor frame uses super-long fifth-wheel pick-up plate as well as plate reinforced cross member.
牵引车车架采用了超长的鞍座连接板及连接板加强横梁。
It has been introduced the principle and structure of necking machine for the front cross member pipe.
介绍了前横梁管材缩口机的原理及结构。
Feed the belt strap in direction of arrow around the roll cage cross member into the adjustable slider.
将安全带按箭头方向绕着防滚翻保护架横梁穿入调节滑块。
Lastly, a research for springback reason and a compensation for tool surface of underbody cross member panel were performed using JSTAMP.
最后,研究了回弹的原因和介绍了使用JSTAMP对车身底座横梁板执行回弹补偿的过程。
These center bearings carry an intermediate support structure which is rotatable thereon along a second axis perpendicular to the axis of the cross member.
这些中心进行的中间轴承支撑结构是可旋转沿垂直于横梁第二轴轴报告。
Analysis and explorations are made to the rupture phenomena of te first cross member in SH6700 light bus floor. 3-structure improvement plans are put forward on the basis.
针对SH6700轻型客车地板第一横梁的断裂现象进行了分析和探讨,在此基础上提出了三种结构改进方案。
Fitting rear cross member to the bodyfit rear cross member on the body and use a beam compass to adjust to the dimension on the right and left. secure the rear cross member with tensioning clamps.
将后横梁装配到车身将后横梁装配到车身上并使用长腿圆规调节左右两侧的尺寸。用张紧卡箍固定后横梁。
Meanwhile, the cross member also employs diversified structures which enable the standard and luxury model frame have less deadweight, whereas the economic frame model has more load-carrying capacity.
同时横梁也采用了不同的结构形式,使标准型和豪华型车架具有较轻的自重,经济型车架具有更强的装载能力。
Before each build, team member from cross function department should sign off in readiness sheet to confirm status of each function.
在每次生产前,项目成员应当在准备就绪表上签名确认各职能部门准备的状态。
In order to ensure the normal operation of traffic in construction the continuous box beam 's construction adopts cross beam as supporting system and Bailey member bars as abutments.
为保证在施工期间的交通正常运行,连续梁的施工特采取贝雷杆件组拼支墩和横梁作为支撑系统。
Once the proper alignments and angles have been achieved, the cross-members are ready for welding. A solid fillet should be welded around the entire circumference of each cross-member tube.
一旦正确的路线和角度已经实现,交叉成员焊接准备。一个坚实的鱼片应该管焊接周围人的整个圆周每个交叉。
The proposed method is applicable for the thin-walled member of any cross section with any boundary condition.
本方法适用于任意横截面形状和任意边界条件的薄壁杆件。
Based on the academic analysis, a biaxial bending member is equivalent to a single bending member by the rule of equivalent cross section.
在分析大量文献资料的基础上,采用“等效截面”将双向受弯构件转化为单向受弯构件。
Weld the cross-member gusset as shown in the drawings below.
焊缝交叉成员扣板如下图所示。
Conclusion Between the popular season we should attention family member cross infection's protection and carry on the effective sequential treatment.
结论流行季节注意家庭成员之间交叉感染的防护及进行有效的序贯治疗。
A frame of the commercial vehicle comprises a front cross-member (2) for the connection of two longitudinal-members (3).
商用汽车的车架,包括用于连接两个纵梁(3)的前横梁(2)。
Team member from cross function should provide their drafted schedule for this project during initial stage, also will develop their schedule fully in half month.
项目组成员将在初期提供他们粗略的时间表,然后在半个月内完成最终的计划时间表。
The power input rotary member and the power output rotary member contact respective slanting section of one of the slanting portions with V-shaped cross section.
动力输入构件和动力输出构件分别与该弹簧座的具有V形截面的倾斜部分之一相接触。
In order to avoid a singular solution, we keep the dimension of the truss for a given topology unchanged by giving the truss member to be removed a tiny cross-sectional area.
为了避免结果奇异,在优化过程中,给被删去的构件一个微小的截面积,使一个给定的拓扑组的结构维数保持不变。
Using the conception of equivalent cross-section, the formula of elastic carrying capacity at the larger end of the tapered member is suggested.
采用楔形构件等效截面特性的概念,结合我国规范推导出以大头截面为计算截面的受弯稳定性计算公式;
A solid fillet should be welded around the entire circumference of each cross-member tube.
一个坚实的鱼片应该管焊接周围人的整个圆周每个交叉。
The experimental study of steel structural member with a new type of cross section is presented.
主要介绍了一种新型截面的钢结构构件的试验分析。
Prior to welding these clamps to the frame, insure that they both are pointing straight forward and directly on top of each cross-member.
在此之前这些焊接夹具,框架,确保它们都是指向每个交叉成员直线前进,并直接在上面。
Prior to welding these clamps to the frame, insure that they both are pointing straight forward and directly on top of each cross-member.
在此之前这些焊接夹具,框架,确保它们都是指向每个交叉成员直线前进,并直接在上面。
应用推荐