The HA-5002 is a monolithic, wideband, high slew rate, high output current, buffer amplifier.
的HA- 5002是一款单片，宽带，高转换率，高输出电流，缓冲放大器。
If the efficiency of servo amplifier is considered, it is practicable that the power supply voltage is about 3 times as large as the servo amplifier output voltage corresponding to rated current.
若考虑伺服放大器效率及电源功率等因素，伺服放大器电源电压应取额定输出电流所对应的伺服放大器输出电压的3倍左右为宜。
After discussing how the input offset current influences the output of operational amplifier, the optimal relationship between peripheral impedance is obtained.
通过讨论输入失调电流对集成运算放大器输出的影响，推导出集成运算放大器外围阻抗的最佳取值关系。
If the output voltage is less than the predetermined voltage level, a transconductance amplifier generates a current that sets an overload flag.
如果输出电压大于预定的电压电平，则跨导放大器产生使过电压标志置位的电流。
Two kinds of methods such as lead net rectification and negative feedback rectification are proposed, which can increase the output current speed of the current amplifier.
提出采用超前校正和负反馈校正提高电流放大器输出电流响应速度方法。
This situation can arise, for example, when a transconductance amplifier feeds an output current i0 to a load resistor RL, but the overall circuit is considered to give a voltage gain VL/Vi.
例如当一个互导放大器提供一输出电流i0到负载电阻RL，而全部网络给出电压增益为VL/Vi时，就可出现这种情况。
The technology of temperature compensation and cascade current mirror was used, and the output of two stage amplifier was used for the bias of itself.
电路运用带隙温度补偿技术，采用共源共栅电流镜，两级运放输出用于自身偏置电路。
Increasing the input signal to the amplifier results in a corresponding increase in output current to the valve solenoid.
增加放大器地输入信号会导致输出到阀电磁铁的电流相应的增加。
Typical analysis of the constant-current resistance and the output current error, The writer gives the analysing process by means of operational amplifier.
从恒流源内阻和形成输出电流误差两个方面，给出用运算放大器构成压控恒流源的分析结果。
A current-driven common source amplifier which is biased on class AB constitute the output stage.
由偏置在AB类的电流驱动的共源放大器构成输出级；
Single Supply, Low-Power, High Output, Current Feedback Amplifier.
单电源，低功耗，高输出电流反馈放大器。
After start-up, the low amplifier output impedance reduces reference current variations due to the current through R1.
完成启动后，放大器很低的输出阻抗将会降低因流经R1的电流不足以影响稳压管上的电压稳定性。
Coaxial cables for the high voltage and PMT output current signals connect between the detector housing and the amplifier unit.
PMT高压电源线盒信号输出线连接了探测器封装和放大器单元。
The output of the amplifier (electrical current) is controlled by the input signal so with zero input the output current is also zero.
放大器地输出(电流)由输入信号控制，所有零输入信号，电流输出也是零。
The output of the amplifier (electrical current) is controlled by the input signal so with zero input the output current is also zero.
放大器地输出(电流)由输入信号控制，所有零输入信号，电流输出也是零。
应用推荐