A prefix of cylindrical roller bearing codes identifies the design.
一个前缀的圆柱滚子轴承代码标识设计。
Besides, the research of ceramic cylindrical roller bearing is less.
而关于陶瓷材料圆柱滚子轴承的研究则更少。
Wrist pin end carried on double row long cylindrical roller bearing.
连杆小端装有双列长圆柱滚子轴承。
Most cylindrical roller thrust bearings are single-direction bearings.
大多数推力圆柱滚子轴承是单方位轴承。
At last, the rigidity of the preloaded hollow cylindrical roller bearing is researched.
最后，又对预负荷空心圆柱滚动体轴承的刚度进行了研究。
The basic shape of the rollers and raceways of cylindrical roller bearings is cylindrical.
圆柱滚子轴承的滚子和滚道的基本结构类型是圆筒形的。
But the researches on the hollow cylindrical roller bearing are very late in our country.
而我国对空心滚动体轴承的研究起步较晚。
The needle roller bearing is a cylindrical roller bearing with thin, long rolling elements.
滚针轴承是拥有薄的，长的滚动体的圆柱滚子轴承。
On request NKE full complement cylindrical roller bearings are produced to other tolerance classes.
根据要求，NKE的满装圆柱滚子轴承生产其他公差等级。
Such as cylindrical roller bearings, tapered roller, needle, ring and other on-line automatic detection.
如轴承圆柱滚子、圆锥滚子、滚针、套圈等的在线自动检测。
The article gives the key elements to select four-row cylindrical roller bearings for plate mill application.
简要介绍轧机用四列圆柱滚子轴承的选用要点。
In this way, code NU2308 is obtained for a cylindrical roller bearing with a 40 mm bore diameter (Section 1.6).
用这种方法，获得了NU2308为代码的孔直径40毫米的圆柱滚子轴承(16节)。
In this paper, the design method of full complement with self-retained cylindrical roller bearing is discussed.
讨论满滚子径向自锁圆往滚子轴承的设计方法。
Rolling bearings. single - row cylindrical roller bearings. chamfer dimensions for loose rib and non - rib sides.
滚动轴承。单列圆筒形滚子轴承。平挡圈和非凸缘边的倒圆角尺寸。
To compute the stress of the cylindrical roller bearings under loading is a typical boundary nonlinear contact issue.
圆柱滚子轴承在载荷作用下的应力分析，是典型的边界非线性的接触问题。
With all cylindrical roller thrust bearings, increased sliding friction can occur on the end of the cylindrical rollers.
所有的圆柱滚子推力轴承，滑动摩擦增加，可能会出现圆柱滚子的结束。
The results show that the system stability is directly influenced by the radial clearance of cylindrical roller bearing.
结果表明：圆柱滚子轴承的径向游隙直接影响着滚动轴承-双转子系统的稳定性。
And its dynamic load model is proposed on the assumption that there is a virtual roller in the cylindrical roller bearing.
进而提出了圆柱滚子轴承的动态刚度模型和动态阻尼模型。
Due to their specific kinematic behaviour, cylindrical roller thrust bearings are only suitable for low speed applications only.
由于其特定的运动行为，圆柱滚子推力轴承只适合低速应用。
Cylindrical roller bearings are used in machine tools, transmissions, vibration machines, and as wheelset bearings for rail vehicles.
圆柱滚子轴承用于机械工具，传输，振动机器和作为轮副轴承用于轨道车辆中。
Finally, the results of stiffness analysis and experiments completed on a high-speed cylindrical roller bearing were given in the paper.
结合具体的高速圆柱滚子轴承给出了刚度分析结果及其与实测结果的比较。
Up to medium size, cylindrical roller bearings are generally fitted with a cage of glass-fibre reinforced polyamide or a pressed sheet-steel cage.
直到中号尺寸，圆柱滚子轴承一般都配置一个玻璃纤维增强尼龙保持架或一个钢板冲压保持架。
For tapered roller large end and sliding friction between the inner wall, the speed limit is often lower than the same size cylindrical roller bearings.
因圆锥滚子大端与内圈挡边之间滑动摩擦，其极限转速往往低于同尺寸的圆柱滚子轴承。
The researches on the preloaded hollow cylindrical roller bearing are much less, no research paper is found about this aspect in the magazine at home by now.
而关于预负荷空心圆柱滚动体轴承的研究更是少之又少，到目前为止，在国内的期刊和杂志上还没有发现关于这方面的研究论文。
The cage which retains the cylindrical rollers of the cylindrical roller thrust bearing is an injection moulded glass fibre reinforced polyamide 6, 6 cage (FIG 6).
保持圆柱滚子推力轴承圆柱滚子的保持架，是注射成型的玻璃纤维增强聚酰胺6.6保持架(图6)。
It referenced the structural arrangement of similar vehicle, this design transmission bearing according to national standard that choose the cylindrical roller bearing.
参考同类车型的结构布置，本设计变速器轴承按国家标准选择圆柱滚子轴承。
The related position dimensions of rivet on machined solid cage with square rivet head used in cylindrical roller bearings directly effect assembly and riveting quality.
圆柱滚子轴承方铆头车削实体保持架铆钉头相关部位尺寸直接影响轴承的装配和铆合质量。
To avoid sliding that occurs in cylindrical roller thrust bearings, the taper Angle of the rollers is selected so the extended contact lines intersect on the bearing axis.
为了避免推力圆柱滚子轴承发生滑动，滚子的锥度要合适以至于扩大的接触线可以与轴承轴相交。
Via analysis of the end wearing of the roller end of the short cylindrical roller bearing, the edges of the inner and outer rings, the corresponding measures are given out.
通过对短圆柱滚子轴承滚子端面、内外圈挡边端磨现象的分析，提出了针对性的措施。
Via analysis of the end wearing of the roller end of the short cylindrical roller bearing, the edges of the inner and outer rings, the corresponding measures are given out.
通过对短圆柱滚子轴承滚子端面、内外圈挡边端磨现象的分析，提出了针对性的措施。
应用推荐