The defects of surface of cast iron hardware and its influence on the quality of zinc deposit were analyzed.
分析了铸铁五金件表面存在的缺陷及其对镀锌层质量的影响。
This article analyzes the main factors and selection of rational cutting conditions influencing the surface flatness error and other defects in sawing marble plates with diamond saw blade.
本文分析了金刚石框锯在锯切大理石时，引起表面平面度偏差和其它缺陷的主要因素以及合理工作条件的选择。
This paper describes the methods of controlling the frame quality in terms of process design, mould design, control of deformation and defects from welding surface treatment, etc.
从工艺设计、胎具设计、控制焊接变形和缺陷、表面处理等各环节实行严格的品质控制，多年来生产出多种型号的车架全部为合格品。
The main surface of the workpiece, the assembly surface should be first processing, thus early detection of defects in the workpiece surface may be the main.
工件的主要表面，装配基面应先加工，从而及早发现毛坯中主要表面可能存的缺陷。
Minor cracks holes and surface defects shall be made good with exterior grade water-mixed filler or masonry cement before application of the primer or first coat of paint.
在第一次应用或涂底漆之前，较小的裂缝、孔及表面缺陷应采用浆、水混合填料或水泥浆和砌浆进行填塞及填充。
PITTED: Small indentations appearing as black dots on finished surfaces of any piece of product; undesirable surface defects.
麻面：在任何成品零件的表面上出现的小的黑色的麻点，这是不希望的缺陷。
One of the most prevalent defects of hard drives is bad sectors on the disk surface.
其中一个最普遍的缺陷，硬盘驱动器是坏扇区对硬盘的表面。
The shunt resistance represents the loss due to surface leakage along the edge of the cell or due to crystal defects.
分流电阻表示由于沿电池边缘的表面漏流或晶格缺陷造成的损耗。
Defects detection for texture surface is one of the important research problems in machine vision, and can be widely used in surface quality control of different products.
纹理表面的瑕疵检测是机器视觉的一个重要研究课题，已经广泛用于各种产品表面质量控制。
Statistic data shows that 65% of bearing invalidation formats is induced by surface defects of steel balls.
实验统计表明：在轴承的失效形式中，由于钢球表面的缺陷而引起的裂纹、裂缝造成的轴承失效达65%。
The purpose of weld guide bending test is to detect plasticity of welding joint, welding process and surface defects of materials.
焊缝导向弯曲试验的目的是检查焊接接头的完好性和塑性以及材料的焊接工艺和表面缺陷。
Huanghua pear is an important fruit in China. The fruit diameter and surface defects are important indices in the classification of Huanghua pear.
黄花梨是中国的一种重要水果，果径和果面缺陷面积是黄花梨分级的两项关键指标。
A surface inspection system for cold rolled strips is introduced, which is used in on-line detection and recognition of surface defects on cold rolled strips.
介绍一套目前正在开发的冷轧带钢表面质量在线监测系统，该系统用于在线检测和识别冷轧带钢的表面缺陷。
Defects due to an unsatisfactory rate of teeming. This kind defects include splashing, rippled surface, and laps or folds.
由于浇注速度掌握不好而引起的缺陷。这种缺陷包括飞溅、波皱面以及重皮或折叠。
To increase nucleation density, the methods of introducing defects on substrate surface are more effective in the diamond thin films growth by means of the low pressure vapor phase deposition.
在低压气相生长金刚石薄膜过程中，通过在衬底表面引入缺陷，通常是一种行之有效的提高成核密度的方法。
The reason and prevention of four kinds defects including surface wrinkled skin (carbon built-up), chock, blow hole, deformation, was introduced in this part of the article.
本部分主要介绍表面皱皮（积碳）、呛火、气孔、尺寸超差及变形等缺陷的产生原因和防止方法。
The grade identification technology of surface defects of green orange based on computer vision was studied.
应用计算机视觉研究了绿橙表面缺陷的分级检测技术。
In this paper, we will introduce the computer programming methods of several special functions which are used in calculation of the surface defects' scattered field by T-matrix method.
本文介绍用t矩阵方法来计算表面缺陷散射场时所用到的几个特殊函数的计算机数值编程方法。
The results showed that the fracture was of typical fatigue fracture, and surface defects were the main factor resulting in the failure of the air valve spring.
结果表明，断裂呈现典型的疲劳断裂特征，材料表面缺陷是引起该弹簧疲劳断裂的主要原因。
Analysis is made on the dark lines defects occurring over the working surface of flange by measurement with the optical microscope, Scanning electro microscope (SEM) and electronic probe.
针对法兰盘加工面上出现的黑纹缺陷，采用光学显微镜、扫描电镜和电子探针等测试方法对其进行了分析。
Types of and causes for the surface defects of the CC round billet for pipe - rolling with mandrel mill are analyzed, and quality improvement measures proposed.
简要分析了连铸连轧圆管坯表面缺陷的类别和形成原因，提出了改进圆管坯质量的措施。
This paper introduced the characters of surface defects of hot strips and data mining thesis briefly at first.
本文首先对热轧带钢表面质量缺陷发生的特点及数据挖掘理论进行了简单介绍。
The surface defects of silver COINS was analysed with auger electron spectroscopy (AES), Scanning electronic microscope (SEM) and energy dispersive spectrum (EDS).
采用扫描电镜、能量色散谱和俄歇电子能谱检测方法，对银币表面缺陷进行了分析。
Two-stage-inspections method for the surface defects of rolled strip was briefly introduced.
简要介绍了带钢表面缺陷二级检测的方法。
Defects of crankshaft surface and body will produce important effect on engine reliability. This paper probes into flaw detection technology of forging steel and nodular cast iron of crankshaft.
曲轴表面及本体的缺陷，对发动机的可靠性有重要影响，对锻钢和球墨铸铁曲轴的探伤技术进行探讨。
The holes and defects appear at the top surface of castings during the common plain carbon steel is produced by V-process.
用V法铸造生产普通碳钢铸件易产生氧化缺陷，表现在铸件上表面有麻坑和缺损等。
Based on the principle of model recognition, we can quickly and accurately identify the impedance charts of various defects on the surface of pump-rod.
利用计算机模式识别原理，快速、准确地识别出抽油杆表面多种缺陷的阻抗图。
Experiment showed that the testing system was fit for detecting the surface and near surface defects of steel pipe.
钢管裂纹的检测试验表明，该系统能很好地实现钢管表面和近表面裂纹的检测。
Experiment showed that the testing system was fit for detecting the surface and near surface defects of steel pipe.
钢管裂纹的检测试验表明，该系统能很好地实现钢管表面和近表面裂纹的检测。
应用推荐