Developed excogitates of two decumbence and one horizontal molding die realized the increasing height of branch pipe of heat pressure tee.
研发出了两个横梁和一个水平成型模具，实现了热压三通支管高度的增加。
To find out the answer to this question and see whether your height, largely a genetic gift (thanks mom and dad), will affect when you will die, read the next page.
要找到这个问题的答案，看看你的身高(大部分取决于基因的馈赠，谢谢爸爸妈妈)是否影响你能活多久，请看下一页。
An alternative theory is that cats above this height simply die more often or have much more serious injuries and so aren’t brought into the veterinarian clinic at all. This seems likely enough.
另一个理论是这样讲的，从七层以上高度降落的家猫死掉的更多或者伤得太重根本没可能带回诊所，这也是非常可能的。
Ahigh fall is certainly among the speediest ways to die: terminalvelocity (no pun intended) is about 200 kilometres per hour, achievedfrom a height of about 145 metres or more.
从高空坠落也很可能迅速的死去。 从145米以上的高度掉下来到地面时能达到200公里的时速。
Developed excogitates of two decumbence and one hovizoutal molding die realized increasing height of branch pipe of heat pressure tee and reducing radius of synodical arc of tee.
研制出两套立式模具和一套卧式模具，实现了用工艺方法增加热挤压三通支管高度，缩小三通相贯区内拐角处圆弧半径的目的。
A combined extruding die of new structure was designed to bring 3150kn oil press into its full play under the condition of limited shut height.
在设备闭合高度有限的情况下，设计了1副结构新颖的组合式挤压模具，使3150kN油压机设备能力得到了有效的发挥。
Further I make a detail list of the needed components, and fix the die shut height reasonably; draft the assembly drawing.
其次还列出了模具所需零件的详细清单，并对模具闭合高度进行了合理的确定，设计出了装配图。
This article mainly introduces the features of different changes for several bending height of Z-shape parts, quick changes die and multiple use.
介绍Z形件几种弯曲高度的不同变换，以及换模快且多用等特点。
The invention solves the problem of increase of the whole height, thus optimizes the structure of the die carrier.
本发明较好地解决了模架的整体高度增加的问题，从而优化了模架的结构。
Analyzed the trimming methods when the thick of plate less than two times bending height, introduced the die structure, design points and its working process.
分析了板材弯曲高度小于两倍料厚时，采用切边方法，并介绍了切边模结构、模具的设计要点及其工作过程。
Die stress analysis results show that the deformation of the die core increases with welding chamber height. For the stress distribution, there exists a best welding chamber height.
模具变形分析结果表明，随着焊合室深度增加，模芯变形程度增大，对应力分布来说，存在一个最佳的焊合室深度。
Specially set structure and attach fine-adjustment protection device, flexible adjustments height and force of cutting, can prolong service life of cutting die and cutting rubber board.
特有设定构造，附微调保护装置，灵活调设裁断高度和裁断力度，能延长刀模和裁断板的使用寿命。
The height is measured vertically from the top to the bottom of the tablet while it is in the tablet die in which it is fully compressed, after compression has been completed.
在完成压制后，在药片位于将其充分压制的药片模头中时，从药片顶端至底端垂直测量高度。
As far as the practicability of the die for the thickness, the height of the block would be adjusted when extruding the sheets with different thickness.
考察了宽幅机头对于不同厚度片材的挤出适应性，得到结论：当生产不同厚度的片材时， 阻尼块高度需要调整。 关键词：高分子防水卷材，三维有限元，流场分析，挤出机，机头。
In addition, application of bolt of height-fixed bushing and inner six corners in the elastic discharging device made die installation and maintenance easier.
另外在弹性退料装置中将卸料螺钉改用为定高套加内六角螺钉装置，使模具在装配和维修时得到了方便。
In addition, application of bolt of height-fixed bushing and inner six corners in the elastic discharging device made die installation and maintenance easier.
另外在弹性退料装置中将卸料螺钉改用为定高套加内六角螺钉装置，使模具在装配和维修时得到了方便。
应用推荐