Double eccentric shaft vibration exciter is the source of linear vibration.
振动给料机由双偏心轴激振器提供直线振动源。
Abrasive machining for eccentric shaft of rolling cut type sizing shear has been described in this paper.
介绍用磨削方式加工临钢滚切式定尺剪偏心轴的方法。
The succeed of rolling of eccentric shaft in front and back brake will expand the application of wedge rolling.
分析了前、后制动蹄偏心轴轧制的工艺设计，推导了偏心部分的孔型曲线方程，对零件轧制的工艺调试也作了简要分析。
One end of a paper transmission drum is provided with an eccentric shaft sleeve and a driving mechanism is at the lower part of the eccentric shaft sleeve.
在传纸滚筒一端上带有偏心轴套，偏心轴套下部有一驱动机构。
Main products are: Continental C Series jaw crusher machine and its components, a moving jaw, front plate, back plate, dental plates, side guard, jaw plate, eccentric shaft, flywheel, bearing, etc.
主营产品有：欧式C系列颚式破碎机整机及其部件，有动颚、前板、后板、牙板、边护板、颚板、偏心轴、飞轮、轴承座等；
Because an eccentric can be attached anywhere along a shaft, it is unnecessary to form any part of the shaft into a crank.
由于偏心轮可装于轴的任何部位，不必把主轴作成曲柄。
In this paper the demands, the lowest mass design principle of balancer shaft of fan type and eccentric circle type balancer mass are analyzed.
分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。
The cross wedge rolling deformation process of shaft parts with eccentric section was simulated with three-dimension finite element soft LS-DYNA by using elastic-plastic finite element method.
利用三维弹塑性有限元软件L S- DY NA对一种典型偏心轴类零件楔横轧成形进行了数值模拟，分析了其成形过程、应力应变场分布及工艺特点。
At one end of the inner ring, the bearing is clamped to the shaft with an eccentric locking ring (Figure 1.7) or with two setscrews (Figure 1.8).
在内圈的一端，轴承通过偏心锁定环(图1.7)或者两个定位螺钉(图1.8)被固定在轴上。
Experimental techniques such as optical microscopy and scanning electron microscopy were used to study fracture of press eccentric gear main shaft.
采用扫描电镜及光学显微镜对压力机偏心齿轮主轴断口进行了系统的分析。
A new methodology of cross wedge rolling of shaft parts with eccentric section was presented, and the roller profile surface of tools was provided.
提出了一种偏心轴类零件楔横轧成形新工艺，给出了楔横轧成形偏心轴类零件轧辊的辊型曲面。
Motor upper and lower guide bearing wear limit, to replace the bearings, rotor shaft eccentric wear limit, to replace bushings;
电机上下导轴承磨损极限，要更换轴承；转子上下轴套偏磨极限，要更换轴套；
Vibrating chamber is equipped with eccentric wheel, rubber soft tubes, main shaft and shaft-bearing, etc.
振荡室内有偏心轮、橡胶软垫、主轴、轴承等组成。
The adjustable eccentric weight can drive to the Central Line of main shaft through motor. Under the unstable state, it produces centrifugal force that makes raw material form vortex in the sieve.
可调节的偏心重锤经马达驱动传达到主轴中心线，在不平稳状态下，产生离心力，使物料强度改变在筛内形成轨道旋涡。
The adjustable eccentric weight can drive to the Central Line of main shaft through motor. Under the unstable state, it produces centrifugal force that makes raw material form vortex in the sieve.
可调节的偏心重锤经马达驱动传达到主轴中心线，在不平稳状态下，产生离心力，使物料强度改变在筛内形成轨道旋涡。
应用推荐