The exhaust gas temperature is an index for the economy estimation of a thermal power plant.
排烟温度是衡量热源厂热经济性的一个指标。
On the premise of security operation, to decrease the exhaust gas temperature and to control surplus air are both effective measures of energy-saving.
因此在考虑加热炉安全运行的前提下，降低排烟温度以及控制过剩空气系数是比较有效的节能措施。
From the perspective of functional analysis, the prediction of the aeroengine exhaust gas temperature could be seen as a functional approximation problem in nature.
从泛函分析的角度出发，将航空发动机排气温度预测问题转换为一种泛函逼近问题。
The reduction of the engine exhaust gas temperature is one of the key points of this technology, which will influence the safe operation of the entire filter system.
在这一技术中，发动机的排气降温是关键环节之一，它直接影响到整个尾气微粒过滤系统的工作安全性。
The reliable improvement methods were suggested and carried out. The lower gas velocity causes more serious ash deposit, which led to the higher exhaust gas temperature.
烟气速度偏低将导致积灰严重，影响传热，这是排烟温度高的主要原因。
Higher gas inlet temperature, lower steam pressure or pinch point temperature difference lead to lower exhaust gas temperature, larger evaporation and higher efficiency;
提高进口烟气温度、降低蒸汽压力或减小节点温差，均可显著降低设计出口烟气温度，从而增大蒸发量，提高热效率；
The exhaust gas temperatures rise and variation during EUIII test cycle and its impact on the light-off time, ceramic temperature, dynamic response behavior and emission results were studied.
试验研究了摩托车在EUIII测试循环工况下的排气温度变化，以及对于两种氧传感器起燃时间、陶瓷体温度变化、动态响应特性和排放的影响。
Because the boiler's exhaust gas temperature is taken as the intermediate variable, to be used as the input of two other models, the predictive precision of the whole model is markedly raised.
由于综合模型采用了锅炉排烟温度预测模型的输出为中间变量，并作为另外两个模型的输入，因而大大提高了整个模型的预测精度。
The formation mechanism of bulging and cracking of combustor inner liner and his influence on gas turbine exhaust temperature dispersity was analyzed.
分析了火焰筒鼓包和破裂的形成机制对燃气轮机排气温度分散度的影响，提出了相应措施，以防止因燃烧恶化对热通道部件的伤害。
Turbine exhaust temperature is an important thermal parameter in gas turbine power plants and its measured value is affected by sensors state.
燃气轮机电厂实际运行中，涡轮排气温度是一个重要的热参数，其传感器的状态直接影响到排气温度观测值。
The analysis shows that once the exhaust temperature changes, the changes of output and thermal efficiency for gas turbine set are significant.
分析说明了排气温度发生变化时，燃气轮发电机组的出力和热效率的变化比较显著。
This paper analyses the boilers operation and measure data, then finds out and summarizes the causes of higher exhaust temperature of the fuel gas.
对其运行及测量数据进行了分析，发现并总结了锅炉运行中排烟温度升高的原因，并针对其提出了相应的整改措施。
Into the tail flue of fly ash due to the low temperature, has a certain hardness, so primary heating surface with flue gas exhaust pipe, the wear and tear on the wall.
蒸汽锅炉进入尾部烟道的飞灰由于温度较低，具有一定的硬度，因此随烟气初级受热面排管时，会对管壁产生磨损作用。
The second class absorption heat pump can get hot water or vapour using heat potential difference of middle temperature exhaust gas and lower temperature sink.
第二类热泵可利用中间温度的废热与低温热源之间的热势差，制取热量少但温度高于中温废热的热水或蒸汽。
During the burning exhaust gas disposal unit, this kind of steel also has choiceness anti-corrosions effect for vitriol dew point corrosion resulted from low temperature exhaust gas.
在燃烧的废气处理设施中，这种钢对低温废气引起的盐酸露点腐蚀也有优良的防腐效果。
The invention relates to a method and a device for measuring the temperature of an exhaust gas flow in an exhaust line of an internal combustion engine.
本发明涉及一种用于测量内燃机的排气段中废气流温度的方法及装置。
Result shows that decreasing fluid rate and shortening switching time can decrease the temperature of the exhaust gas and increase the recovery rate of waste heat.
结果表明：适当降低流过蓄热体的气体流速，缩短四通换向阀的切换时间，可降低烟气的出口温度，提高系统的余热回收率。
By using exhaust heat, methanol is dissociated to methanol dissociated gas in the condition of high temperature and catalyst.
本研究通过利用尾气余热，让甲醇在高温以及催化剂的条件下催化裂解而得到甲醇裂解气。
Research shows that the burner is based on high-temperature air combustion, zoned combustion and exhaust gas recycle.
该烧嘴综合高风温无焰燃烧、分区燃烧及烟气再循环等技术；
Pump will not overheat: powered by compressed air in the exhaust is an endothermic process of expansion, pneumatic pump when the temperature is lower, non-harmful gas emissions.
泵不会过热：压缩空气作动力，在排气时是一个膨胀吸热的过程，气动泵工作时温度是降低的，无有害气体排出。
Its hydraulic medium temperature control, gas exhaust flow, starting current control and so on are improved.
在液压介质温度控制、排气流程、降低起动电流等方面进行了改进。
Its hydraulic medium temperature control, gas exhaust flow, starting current control and so on are improved.
在液压介质温度控制、排气流程、降低起动电流等方面进行了改进。
应用推荐