The beam has a constant flexural rigidity.
该梁具有常数弯曲刚度。
Testing mechanism of flexural rigidity is described.
描述了抗弯刚度的测定机理。
Specimens'fatigue flexural rigidity reduces gradually while cycle time increasing.
随荷载循环次数的增加，试件的刚度逐渐减小。
The single-chorded plane space truss have the low flexural rigidity out of plane because of lacking bottom chord.
单弦杆平板网架由于无下弦杆，因而具有平面外抗弯刚度较低的特点。
The flexural rigidity of each wall pier under tensile condition was quite different from that under compressive condition.
墙肢的刚度，由于其受拉、受压的不同，也有显著区别。
We get the CFRC can increase the flexural rigidity, reduce the size and number of the crack, increase the bearing capacity.
可以得出采用碳纤维布加固的钢筋混凝土梁能有效提高抗弯刚度，减小裂缝尺寸及数量，提高承载力。
Taken the lateral flexural rigidity of stiffener, the flexural rigidity in its plane and the torsional rigidity into consideration.
考虑了筋的侧向抗弯刚度及在其平面内的抗弯刚度和抗扭刚度。
The experimental results show that there exists a good linear relation between the flexural rigidity parameters measured by any other method.
实验结果显示出振动法与其他方法测得的弯曲刚度指标间存在着良好的线性相关。
Fabric Stiffness Tester. To determine the bending height, flexural rigidity and bending modulus of fabric by simple procedures and calculation.
织物硬挺度测试仪，可通过简单操作及计算测出织物的弯曲高度、弯曲刚度、弯曲模量。
The structural strength and flexural rigidity of the fuselage main frame are computed and verified by CAE system software and the results are analyzed.
应用CAE系统软件计算承力密封框的刚度和强度，并分析了计算结果。
In the model, the flexural rigidity of rails, the rigidity of fastenings, the rigidity of subgrade, slide plate, guard rail and spacer block are taken into account.
模型中考虑了钢轨抗弯刚度、扣件刚度、基础刚度、滑床台、护轨及间隔铁等因素的影响。
This paper deals with the principle of measuring flexural rigidity of the fabrics by vibrating reed method. Floxural rigidity values of eight different fabrics were measured.
本文对弯曲共振法测定织物弯曲刚度的基本原理进行了分析讨论和对不同弯曲刚度的八种类型的织物进行了测定；
According to fatigue experiment results, the fatigue equation and equation of surplus strength degradation are built. The law of degradation of flexural rigidity is analyzed.
根据疲劳试验结果，建立了预应力钢纤维混凝土板弯曲疲劳方程和剩余强度衰减方程，分析了抗弯刚度衰减规律。
The dynamic flexural rigidity model and dynamic bending strength model of ceramic were also provided and the material parameters used in the model were obtained by fitting the experimental data.
给出了陶瓷材料的动态抗弯刚度模型和动态抗弯强度模型，并利用试验数据拟合得到了模型中的参数。
The mechanics model of whole process of reinforced concrete beam section flexural rigidity is founded, based on the theoretical analysis the corresponding numerical calculation program is developed.
建立了钢筋混凝土梁截面抗弯刚度全过程分析的力学模型，在理论分析的基础上编制了相应的数值计算程序。
Not only the contact strength between the CAM and the rollers is discussed, the flexural strength and rigidity of the rollers are also discussed.
在机构强度分析中，阐述了凸轮-针轮副啮合齿面接触强度、针齿销的弯曲强度计算和刚度计算。
Not only the contact strength between the CAM and the rollers is discussed, the flexural strength and rigidity of the rollers are also discussed.
在机构强度分析中，阐述了凸轮-针轮副啮合齿面接触强度、针齿销的弯曲强度计算和刚度计算。
应用推荐