The calculation method for bolt pretightening force of tube side gasket and shell side gasket was proposed.
提出了管侧垫片和壳侧垫片螺栓预紧力的计算方法。
This collar acts as a kind of gasket .
这个翻边起一种密封垫的作用。
Class 150: Corrugated graphite-filled steel gasket.
150磅级：石墨填充波纹钢板密封垫。
The gasket among unions adopts food grade material.
快接件的垫圈全部采用可食用级材料；
The gasket cavity should face out to the adjoining flange.
垫圈的空穴应该面向临近法兰的外面。
Repair Kit consists of diaphragm assembly, disc assembly and gasket.
维修组件包括隔膜总成，阀瓣总成和垫圈。
Remove the bolts and lift the pan off the manifolDiscard the gasket.
拆下螺栓并举高盘脱离歧管。扔掉衬垫。
Thankfully, I didn't know the extent of it or I would have blown a gasket.
谢天谢地，我当时并不知道花了这么多钱，否则我早就暴跳如雷了。
The first requirement for a gasket is compatibility with the product being handled.
对于衬垫的第一个要求是同正在操作的产品的相容性。
The urethane liner extends over the flange face to serve as the valve's flange gasket.
这种氨基甲酸乙酯延展覆盖到法兰表面，起到阀门法兰衬垫的作用。
To complete bladder attachment, you will note that the bladder has gasket molded right with the bag.
固定好内胆后，就会注意到内胆有带着袋子的模压垫圈。
Wipe down and then dry the gasket, which is the rubbery band around the door that seals the cold inside.
擦拭干燥那个用来确保密封冷气的包裹在门框周围的橡胶带。
If the gasket is not present or must be replaced, select a replacement compatible for the product involved.
如果垫圈不在或者垫圈必须更换，选择一个同相关的产品相容的替代品。
Regular testing of gasket resiliency and inspection at Receiving due to sensitivity to inconsistent quality.
由于质量差异导致灵敏性差异，因此需要经常进行密封垫弹性测试和检查接受性。
Accurate control of compression through close tolerance of gasket groove and allowance for radial expansion.
通过密封环槽和精确公差和径向膨胀的精确留量实现压缩的精确控制。
Even the diving table, it may be required to replace the waterproof gasket before the loss of waterproof function.
即便是潜水表，也可能在规定更换防水垫圈前就失去防水功能。
If want to use metal gasket, it should be smooth surface narrowed, make its and gaskets of contact area is reduced.
如果要用金属垫片，则应将光滑面缩小，使其与垫片的接触面积减小。
To prevent this from happening, avoid excessive tightening force and install a new gasket with every cylinder change.
为了防止这种情况发生，避免用过大的上紧力，并且每次换钢瓶的时候装一个新的垫圈。
Gasket system is made of double-layered, closed cellular neoprene, with stainless steel O-rings for attaching gloves.
衬垫系统由双层密闭氯丁橡胶组成，带有不锈钢O型环以附带在手套箱上。
For example, wrought iron furniture in the "foot" on to install rubber gasket, lest scratch ground decorates material.
例如在铁艺家具的“脚”上要安装橡胶垫，以免划伤地面装饰材料。
In the low temperature, corrosive medium or vacuum conditions, with special performance should be considered the gasket.
在低温，腐蚀性介质或真空条件下，应考虑具有特殊性能的密封垫。
O seal: usually the dismantled o seal should be changed totally, but the gasket, etc without breakage also can be reused.
形密封：一般经过拆卸的O形密封应全部更换，对其它密封垫片等，只要没有破损，也可以复用。
Generally, the cylinder and the cylinder head bolt together with a thin gasket pressed between them to ensure a good seal.
一般来说，气缸和气缸盖用螺栓紧固在一起，气缸与气缸盖之间用一薄垫圈确保密封良好。
ANSI flange sealing principle is extremely simple: the two bolts each other extrusion flange sealing surface and form a seal gasket.
ANSI法兰的密封原理极其简单：螺栓的两个密封面相互挤压法兰垫片并形成密封。
Installation should be based on the shape of the connection of different sections and sizes of sealing gasket, and placed correctly.
安装应根据连接处形状选用不同截面和尺寸的密封垫，并安放正确。
The user can remove the pipe rubber pad and re assemble it again, and the rubber gasket with serious deformation should be replaced.
用户可将管道胶垫取出后重新组装一遍，对变形严重的胶垫应予以更换。
The pressure of ascension in oil from sealing gasket place, or leakage of oil consumption and cause additional engine leakage faults.
该压力的提升导致机油从密封圈或密封垫处渗漏，造成额外的机油消耗和发动机泄漏等故障。
The Portable Lightweight Ubiquitous Gasket (PLUG) is a sausage-shaped balloon made of polyester and PVC, and fitted with motorised pumps.
这种装置叫做“便携式通用轻型堵漏包”（其英文缩略语为PLUG，正好有塞子的意思）。 它是由聚酯纤维和聚氯乙烯制作的圆柱形气球，并安装了发动机带动的水泵。
The Portable Lightweight Ubiquitous Gasket (PLUG) is a sausage-shaped balloon made of polyester and PVC, and fitted with motorised pumps.
这种装置叫做“便携式通用轻型堵漏包”（其英文缩略语为PLUG，正好有塞子的意思）。 它是由聚酯纤维和聚氯乙烯制作的圆柱形气球，并安装了发动机带动的水泵。
应用推荐