Park Lemke gear pump motor is a kind of parts for cranes.
泊姆克齿轮泵马达是用于起重机的一种配件。
The synchronization gear pump can reduce the radial and boost the work pressure.
同步齿轮泵能够降低齿轮泵径向力，提高齿轮泵的工作压力。
High viscosity gear pump does not generate pressure, it is only the output flow.
高粘度齿轮泵并不能产生压力，它只是输出流量。
Gear pump with the direction of rotation into and out in line with the oil mouth.
齿轮泵的旋转方向要与进、出油口相符。
The product is applied to medium, high-pressure gear pump, ram pump, vane pumps, etc.
产品主要应用于中、高压齿轮油泵、柱塞泵、叶片泵等。
The interlaced gear pump is designed on the basis of analysing flow and pressure pulses.
本文在分析齿轮泵的流量脉动和压力脉动的基础上，设计出一种错齿齿轮泵。
Check valve and relief valve on the output of the gear pump tube had better install a check valve.
止回阀与安全阀在齿轮泵的输出管路上最好安装一个止回阀。
This paper introduces the criterion and some noted problems of gear design for internal gear pump.
本文介绍了内啮合齿轮泵齿轮设计的准则及应注意的几个问题。
Internal gear pump has two kinds of tooth profile namely: involute profile and cycloidal tooth profile.
内啮合齿轮泵有两种齿形即：渐开线齿形和摆线齿形。
These two kinds of internal gear pump working principle and external gear pump working principle the same.
这两种内啮合齿轮泵的工作原理和外啮合齿轮泵的工作原理相同。
Balanced compound gear pump is a new king of hydraulic pump which combines ring gear with external gear pump.
复合式平衡齿轮泵是将内外齿轮泵融为一体的新型液压泵。
This article counter gear pump and hydraulic cylinder's appearance's common breakdown carries on the analysis.
本文对齿轮泵和液压缸的出现的常见故障进行分析。
Use of helical gear in gear pump is an effective measure, which can reduce the mechanical voice and flow pulse.
齿轮油泵采用斜齿轮是降低机械噪声和减小流量脉动的一种有效措施。
The inner leakage, as the major factor, affects the efficiency of the cubage of the balanced compound gear pump.
平衡式复合齿轮泵的内部泄漏是影响其容积效率的主要原因。
The applications of polymer melt gear pump in plastics extrusion and microcellular plastics forming are introduced.
介绍了熔体齿轮泵在塑料挤出成型及微孔塑料加工中的应用。
Continuous Gear pump Metering, Mixing and Dispensing Systems with two rotary pumps driven by a common DC-motor drive.
该产品为连续齿轮泵流量计，由直流电机驱动进行混合和分配操作。
The pump out of the shackles of traditional design, making gear pump in the design, production and use into a new area.
该泵摆脱了传统设计的束缚，使得齿轮泵在设计、生产和使用上进入了一个新的领域。
This article will discuss the design of compensating groove in external gear pump by analyzing the gearing characteristics.
该文主要通过分析齿轮的啮合特点来探讨啮合齿轮泵卸荷槽的设计。
This paper describes the condition of the damaged cargo gear pump used in chemical tanker, gives a new repairing technique.
文章描述了某轮双螺杆货油泵的损坏状况，具体分析了产生故障的原因，提供了相应修理方案。
Internal gear pump is the small gear wheel, the big gear for driven wheel, in work big gear with small gear cocurrent rotation.
内啮合齿轮泵中的小齿轮是主动轮，大齿轮为从动轮，在工作时大齿轮随小齿轮同向旋转。
Flexible set cycloid gear pump rotor pump vane pump with the advantages of a similar volume than pump more than 10% efficiency.
柔性摆线转子泵集齿轮泵与叶片泵优点于一身比同类容积泵的效率提高10%以上。
If the first gear pump operation, or long-term idle after use, preferably in small load or no-load circumstances Xianpao One hour.
齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。
The service life for gear pump is much less than the desired design up to now, which is mainly caused by higher pressure imbalance.
迄今为止，齿轮泵的寿命还远远达不到设计要求，这主要是齿轮泵存在较大的径向不平衡力所致。
The prominent characteristics of gear pump in application to flow metering and fluid transportation were introduced in this article.
介绍了齿轮泵用于流量计量和流体输送时所具有的突出特点。
The gear pump seals the selection principle is not high demand, for the occasion, but by experience, not to replace timely selection.
齿轮泵密封垫的选用原则是，对于要求不高的场合，可凭经验选取，不合适时再更换。
The features and application scope of different alternating and direct current motors used as the drive device of gear pump were compared.
对比了使用不同类型的交、直流电机作为齿轮泵驱动装置的特点和应用范围。
Rationally define the work gear pump speed, gear and the axis of rotation to avoid engaging resonance frequency, can prevent noise intensified.
合理确定齿轮泵的工作转速，使齿轮与轴的转动避开啮合共振频率，可以防止噪声加剧。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
齿顶高系数是设计齿轮时的重要几何参数，也是影响复合齿轮泵流量特性的重要参数之一。
By using melt gear pump, production efficiency and product quality can be improved and production cost can be reduced in the polymer processing.
在聚合物加工中使用熔体齿轮泵可以提高生产效率和产品质量，降低生产成本。
Comparing with involute gear pump, the instant displacement is in direct proportion to the angular velocity of the gear and stable without pulsation.
对比渐开线齿轮泵，单圆弧齿轮泵的瞬时排量与齿轮角速度成正比，且稳定，无脉动。
应用推荐