In most RTOS, the timer interrupt service routine (ISR) executes at every time tick.
在一般的嵌入式实时操作系统中，时钟中断服务程序在每个时钟节拍工作。
When an interrupt occurs the current state of the processor is saved and an interrupt service routine is executed.
当一个中断发生，当前的处理器状态被保存并且中断服务程序开始运行。
When an interrupt occurs, the current state of the processor is saved and an interrupt service routine is executed.
当一个中断发生，当前的处理器状态被保存并且中断服务程序开始运行。
Isr interrupt service routine. code that performs actions necessary to deal with the condition that caused the interrupt.
中断服务程序。在执行操作时处理可能引起中断情况的代码。
This article helps device driver developers test the interrupt service routine as much as possible by simulating the various interrupts.
本文通过模拟各种中断，尽可能地帮助设备驱动程序开发人员测试中断服务例程。
The Orinoco interrupt service routine populates sk_buffs with data received from the WLAN and passes it on to the IP stack via netif_rx.
orinoco中断服务例程用从WLAN接收的数据填充sk _ buffs，并经由netif_rx将它传送到ip栈。
When the interrupt service routine exits control of the processor is returned to whatever part of the software was previously running.
当中断服务程序退出，对处理器的控制权转到先前运行的那个软件上。
When the interrupt service routine exits, control of the processor is returned to whatever part of the software was previously running.
当中断服务程序退出，对处理器的控制权转到先前运行的那个软件上。
The contents of the interrupt service routine: all the lights off, 2 seconds later all the light-emitting diode, another 1 second to return after the break.
中断服务子程序内容：灯全部熄灭，2秒钟后发光二极管全部点亮，再过1秒钟后中断返回。
NET system architecture, and describes the interrupt principle. In order to install the interrupt service routine, we present the way to modify the kernel and the OAL.
NET的系统结构，并详细阐述其中断原理，介绍如何修改内核和硬件抽象层安装中断服务例程。
On software, we take full advantage of the low power modes of the MCU to finish the task in ISR (interrupt service routine), so, the power of system rest with the ISR executive time.
在软件设计上，充分利用所选单片机的低功耗模式，让检测任务在中断服务程序中完成，使系统的功耗主要取决于中断服务程序执行的时间。
Aim Objective: to master the timer T0, T1 of the mode selection and programming methods, to understand the design method of the interrupt service routine, and learn skills in real-time debugging.
实验目的目的：掌握定时器t0、T1的方式选择和编程方法，了解中断服务程序的设计方法，学会实时程序的调试技巧。
At last, in the section of software design, startup code programming, operating system choosing and transplanting, task design, drivers design and interrupt service routine design had been discussed.
最后，在软件设计部分探讨了启动代码编写、操作系统的选择和移植、任务规划和设计、驱动程序设计以及中断服务程序设计。
Code generated for Silicon Labs single-cell C80519XXF by a non-OCG compiler results in an average of 108 cycles to execute the interrupt service routine and main loop overhead for each sample of data.
非ocg编译器针对SiliconLabs单电池供电c 80519 XXF所产生的代码，每次数据采样平均会有108个周期来执行中断服务程序和主循环。
Code generated for Silicon Labs single-cell C80519XXF by a non-OCG compiler results in an average of 108 cycles to execute the interrupt service routine and main loop overhead for each sample of data.
非ocg编译器针对SiliconLabs单电池供电c 80519 XXF所产生的代码，每次数据采样平均会有108个周期来执行中断服务程序和主循环。
应用推荐