It suggested lap joint should be avoided in load carrying structures.
指出了在承力结构中应该尽量避免搭接焊。
The shear strength and elongation of the lap joint increase with the increase of strain rate.
焊点的剪切强度及伸长量随应变速率的增加而增加。
However, further increasing of re content would degrade the shear properties of the lap joint.
而当稀土含量进一步增加时，焊点的强度及塑性均下降。
The results indicate that good lap joint between aluminum and galvanized steel sheet can be made in appropriate parameters.
试验结果表明，铝和镀锌钢能得到成形良好的搭接接头。
Describe the usual problems of lead lap joint about valve electric actuator when working and the improvement of joint process.
阐述了阀门电动装置运行现场导线搭接的常见问题与搭接工艺的改进。
The effect of each inherent strain component on the angular distortion of the lap joint is studied using inherent strain method.
运用固有应变法研究了六个固有应变分量分别对搭接接头焊接角变形的影响。
The waterproof layer of the lap joint should stick (welding) firm, tight sealing, no distortion, fold, curling and blister defects.
卷材屋顶防水层的搭接缝应粘(焊)结牢固，密封精密，不得有扭曲、皱折、翘边和起泡等缺陷。
The finite element method (FEM) is applied to investigate the effect of metal inlay in single lap joint on the stress distribution.
利用有限元方法研究了金属镶嵌对单搭接接头应力分布的影响。
It should be arranged according to kinds signed in drawings when installing, lap joint of anti-rain cover should be level and smooth.
防雨罩安装时应按照图纸中标明的种类进行安装排布，防雨罩之间搭接应平整顺畅。
Through the wire joint pipe should be located in the junction box, the lap joint should be solid, insulating tape wrapping should be uniform and compact.
穿入配管导线的接头应设在接线盒内，接头搭接应牢固，绝缘带包缠应均匀紧密。
The effect of elastic modulus of adhesive on the str ess distribution in aluminium alloy single lap joint was investigated using elastic-plastic finite element method(FEM).
运用弹塑性有限元法，研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头上应力分布的影响。
Taking the form of lap joint as an example, the effect of final assembling deviation affect by the assembly sequence was analyzed by adopting the method of worse condition.
以搭接接头形式为例，采用最坏情况法分析了装配顺序对最终装配偏差的影响。
Results from the experiment show that the load bearing ability of the single-lap joint decreases as the length of the gap increase but the actual shear strength is increased in same time.
结果表明，随着间隙长度的增加，接头的承载能力趋于减小，但接头的实际剪切强度却持续上升；当间隙长度继续增加时，接头的实际强度趋于下降。
The BEM technique for adhesive-bonded structure proves valid by comparing the stress distribution for double lap joint calculated in this paper with that calculated by finite element method.
对双搭接接头进行了边界元应力分析，并和有限元结果进行了对比，从而证实本文方法的有效性。
Using FN-309 adhesive etc. as joint adhesive and, the water-resistant abrasive cloth, R/R or G/G abrasive cloth as the substrate belts the process of abrasive cloth lap jointing was studied.
以FN-309胶粘剂等为接头胶，耐水砂布、全树脂砂布和动物胶砂布等作材料，制作搭接砂带工艺的研究。
The test results show that the reinforced porous brick wall similar tO normal reinforced brick wall on aseismic design, shear resistance of the bar cannot be used very much when using lap joint...
试验结果表明，配筋多孔砖墙与配筋普通砖墙具有相近的抗震性能，水平筋采用搭接接头时不能发挥钢筋的抗剪作用以及端部锚固钢筋具有提高承载力和约束砌体作用等。
The Boeing 737-300 in question was only 15 years old when its skin peeled open along a riveted lap-joint while flying above 34,000 feet (just over 10,000 metres) with 118 passengers on board.
正在讨论的波音737-300型飞机只用了15年。当其外壳沿敲平的上端搭接接头剥落开来时，飞机上的118位乘客正飞行在34000英尺（刚刚超过10,000米）的上空。
The Boeing 737-300 in question was only 15 years old when its skin peeled open along a riveted lap-joint while flying above 34, 000 feet (just over 10, 000 metres) with 118 passengers on board.
正在讨论的波音737- 300型飞机只用了15年。当其外壳沿敲平的上端搭接接头剥落开来时，飞机上的118位乘客正飞行在34000英尺(刚刚超过10,000米)的上空。
The most commonly used joint configurations are the lap, scarf, and butt joints.
最常用的连接结构是搭接，嵌接和平接。
This paper describes the major design problems of three layer lap-joint and multi-stage dosing asphalt sprayer and introduces the selection of the domestic truck chassis.
本文对三层搭接多级定量沥青洒布车的设计主要问题加以论述，并介绍如何正确选用国产汽车底盘。
This article studies the influence of the bolt tightening torque on the fretting damage of LY12CZ aluminium alloy double shear lap bolted joint by experimental and conumerical analysis.
从试验和数值分析两个方面研究了螺栓预紧力矩对LY12CZ铝合金双盖板对接螺纹联接件微动损伤的影响。
The results shown that a deformation-free joint with good weld surface appearance can be obtained with suitable welding conditions for butt-joint and lap-joint of the dissimilar materials.
结果表明，当焊接工艺参数合适时，可以获得表面成形良好、无变形的铝合金与钢的对接接头和搭接接头。
The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.
这些元素可以以不同方式组合在一起，例如：一个搭接接头可能用角接、塞焊和缝焊固定，一个丁字接头可以用一个搭接或槽焊来完成。
The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.
这些元素可以以不同方式组合在一起，例如：一个搭接接头可能用角接、塞焊和缝焊固定，一个丁字接头可以用一个搭接或槽焊来完成。
应用推荐