After the adjustment ended, tighten the lock nut.
调整后，就将锁紧螺母拧紧。
Tang thread fastening and forced lock nut fastening.
即唐氏螺纹紧固及硬锁紧螺母紧固。
Revolving the lock nut 5 anti-clockwise to the suitable position.
逆时针方向旋转锁紧螺母5，使其退到适当位置。
The two-piece Hard Lock Nut is easy to install, requiring only the use of a wrench.
双件套强力锁紧螺母安装简便，只需要一个扳手就行。
After completing adjustments, tighten the lock nut and replace the fast fill lever cap.
在调节完成后，紧固锁紧螺母，重新安装快速进水手柄帽。
Smaller sizes use a lock nut with a locking washer, larger sizes use a nut with locking clip.
小尺寸轴承使用带锁紧垫圈的锁紧螺母大尺寸的轴承使用带锁紧卡箍的锁紧螺母。
Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem.
松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening Angle.
孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。
The feasibility of repetitive use of Fe-based shape memory alloy lock nut has been studied in order to lower the usage cost.
为了降低铁基形状记忆合金防松螺母的使用成本，探索了该新型螺母重复使用的可行性。
The problems in lock nut of roll axis and sleeve of precision rolling mill are analyzed, some measures proposed, good result got.
针对高速线材生产中，精轧机辊轴及隔套锁紧螺母存在的问题进行分析，提出了改进措施，取得了较好效果。
Third, the cartridge installation 1 will push the cartridge into each bracket in a clockwise direction and tighten the lock nut on the screw. 2.
滤筒的安装1。将滤筒推入每个支架中，按顺时针方向旋上并锁紧锁紧螺母。
The fracture of the pump shaft is mainly caused by large size non metallic inclusions and point welding between the lock nut and the pump shaft.
结果表明，大尺寸的非金属夹杂和背帽外缘的点焊是引起泵轴过早断裂的主要原因。
In connection with the bottom cable hand brake handle (usually from the interior cover) has an adjustable offset, with wrench to loosen the lock nut, can stretch brake cable length.
在手刹手柄的底部与钢缆的衔接处(通常由内饰件掩盖)有一个可调的抵偿组织，用扳手松开锁紧螺帽，就能够拉伸刹车钢缆的长度。
It's important to put a lock washer on that last nut, or it can work loose.
重要的是要在最后一个螺母上安装一个防松垫圈，否则它会逐渐变松。
NOTE: If minor leakage occurs, remove lock screw, lock washer and cap and lightly tighten packing gland nut.
注：如果出现少量的泄漏，则拆卸锁紧螺丝，然后锁住垫圈和阀盖，然后轻轻紧固填料压紧螺母。
Hold stem (27) on wrench flats and remove nut (51), lock washer (46), diaphragm plate (60) and diaphragm.
在扳手的平面上握住阀杆(27)并拆卸螺母(51)，锁紧垫圈(46)，隔膜板(60)和隔膜。
To clean or replace parts; shut off supply, loosen lock-nut and back off adjusting screw.
如果要清洗或更换部件，关闭供应管道，松开锁紧螺母，退出调节螺丝。
After the wire thread insert of the hoop of the utility model is installed in the nut, the elastic deformation generated from the radial of the wire thread insert is used to lock the screw.
本实用新型一种环箍是由箍带、锁紧螺母等构成，其特点是所述的锁紧螺母的钢丝螺套有一至多圈呈多边形结构。
Pull out before you want to open on the back of the circular disk lock plate with hooks, nut spanner remove round nut, reoccupy special pull the son will disc pull out.
拉出前，先要开圆盘背面的圆螺母锁片，用钩形扳手拧下圆螺母，再用专用拉子将圆盘拉出。
The mother of nylon lock, metal lock master, K cap, hex nut, cap-shaped, butterfly hats and all kinds of washers, retaining rings, pins and so on.
尼龙锁紧母、金属锁紧母、K帽、六角螺母、盖帽形、蝶形帽及各式垫圈、挡圈、销类等。
Cylinder-lock with 90o stroke, RH and LH application, with clip or nut fixing.
旋程，左右侧应用均可，配有夹子或固定螺母。
Cylinder-lock with 90o stroke, RH and LH application, with clip or nut fixing.
旋程，左右侧应用均可，配有夹子或固定螺母。
应用推荐