Mechanical seal is the key part of submersible sewage pump, the reliability of it decide the submersible sewage pump life.
作为潜水污水泵关键部件的机械密封,其可靠性决定潜水污水泵的使用寿命。
Mechanical seal with tungsten carbide hard wear-resistant, with durable, wear-resistant characteristics, can pump more than 8000 hours of continuous operation safe.
机械密封采用硬质耐磨碳化钨,具有耐用、耐磨等特点,可以使泵安全连续运行8000小时以上。
For motor frame size 180 and above, the inner mechanical seal shall be constructed with a solid block carbon rotating seal face and a solid block silicon carbide stationary seal face.
用于尺寸180以上的电机机架,内置的机械密封结构应该采用一块整体结晶碳旋转密封面和一块整体结晶碳化硅固定密封面。
Mechanical seal design is key to the damage of damping function due to the loss of working liquid of hydraulic shock absorber.
为了防止液压减振器因工作液的损失而丧失阻尼效能,其机械密封结构的设计是重要问题。
Use bellows mechanical seal the cost is too high, but the service life is longer than the first two, maintain or change relatively trouble.
使用波纹管机械密封的的成本太高,可是使用寿命长于前两种,维护或者改换时斗劲麻烦。
Mechanical seal: this type is especially suitable for multi-stage slurry pump in series and without leakage.
机械密封:该形式的密封特别适用于多级串联渣浆泵的密封,完全无泄漏。
Pump shaft seals use mechanical seal, pump top and bottom, respectively, equipped with water injection plug and the drain plug.
泵的轴封采用机械密封,泵体顶部和底部分别装有注水、放泄的螺塞。
This mechanical seal is produced by the mating and slight crushing of the threads when a wrench is applied to tighten the fittings.
当用扳手上紧配件时,这种机械密封会在螺纹配合和轻微的变形来生成密封效果。
Mechanical seal: seal face, gasket and shaft seal, etc parts must be undamaged, otherwise will result in over leakage, sure to change parts with wear and tear or damage.
机械密封:密封面、密封垫及轴封等元件必须完好,否则将导致过度泄漏,对有磨损或损伤的元件必须更换。
Mechanical seal repair process more complicated, after assembly to ensure no leakage of the mechanical seal, mechanical seal technology essential check size.
机械密封检修工艺较为复杂,要保证组装后的机械密封无漏泄,机械密封技术尺寸的校核必不可少。
In manual, automatic sterilization without mechanical seal leak-off filling materials plus acid add alkali peristaltic pump, with beautiful and dignified equipment.
在位灭菌自动手动,无机械密封无泄漏补料加酸加碱蠕动泵,设备美观大方。
Impurity pump mechanical seal after static test, the operation of high-speed rotation of the centrifugal force generated will inhibit the leakage of media.
杂质泵用机械密封经过静试后,运转时高速旋转发生的离心力,会克制介质的泄露。
No mechanical seal leakage or abnormal vibration or noise occurred to the two pumps during operation.
两台泵在运转过程中均未见有机械密封泄漏现象发生,也未见有异常的振动和噪声。
The main mechanical seal is installed in the shaft on the dynamic in Central and fixed pump shell on the static ring for the relative motion between the end to achieve the objective of sealing.
机械密封主要的是靠装在轴上的动环与固定在泵壳上的静环之间端面作相对运动而达到密封的目的。
If mechanical seal is used, adjust the stud on the gland to ensure no leak with it.
使用机械密封时,应调整机封压盖螺柱,使其无泄漏。
Pump body seal part of the series for two sets of mechanical seals, mechanical seal, code-named the upper part 60b, the lower mechanical seal, code-named 60a.
泵体部分的轴封为两套串联的机械密封,上部机械密封代号为60b,下部机械密封代号为60a。
Mechanical seal leakage, the sleeve and the shaft leakage between (inter-axis leakage) is relatively common.
机械密封泄漏中,轴套与轴之间的泄漏是比较常见的。
Direct coaxial structure, high efficiency, small size, light weight, installation and maintenance easy. 6. Mechanical seal, long service life.
同轴直接式构造,效率高,体积小,重量轻,安装保养容易。6.采用机械密封,使用寿命长。
Mechanical seal of cantalever centrifugal pumps in an aromatic complex in Jilin Petrochemical Company experienced frequent failures.
中国石油吉林石化分公司炼油厂芳烃装置悬臂离心泵密封频繁失效。
A sophisticated triple mechanical seal system prevents leakage of the pumped fluid whilst highly polished pump internals minimize damage to the forming polymer chains.
三道机械密封防止介质的泄漏,同时泵内部的高度抛光降低了对形成的聚合物链的损害。
The mechanical seal for light hydrocarbon pump belong to the seal for liquid and gas phases.
轻烃泵机械密封属于汽液两相密封。
The mechanical seal experimental unit of change-resisting work condition was a experimental equipment which can adjust temperature and pressure and operate in all kinds of work conditions.
所设计的变工况机械密封实验台是一套模拟机械密封工作状况的实验设备,能够模拟密封各种正常工况及变工况工作情况。
This paper mainly introduces characteristics and classification, installation and use, as well as repair and maintenance of the power plants pump mechanical seal.
文章主要介绍了发电厂中泵类机械密封的特点与分类、安装与使用以及检修与维护等。
Measurement techniques used frequently for the performance parameters of mechanical seal are presented and the features of various measurement methods are discussed.
介绍了机械密封常规性能参数和特殊性能参数的测量技术,分析了常用测量方法的优缺点。
Existing problems of radial double ended mechanical seal used in reactors and their improvement are introduced, thus lengthening lifespan and reducing the cost of overhaul.
介绍了径向双端面机械密封在反应釜应用中存在的问题及改进,延长了使用寿命,降低了检修费用。
This paper summarizes various factors of causing deformation and their effects on mechanical seal performance.
本文综述了变形的各种因素及其对机械密封性能产生的影响。
The upstream pumping mechanical seal was used as shaft sealing of vacuum plants.
研究了上游泵送机械密封在真空装备轴封中的应用。
Frequent leakage of mechanical seal of quenching oil circulating pump was a hard problem in ethylene production.
急冷油循环泵的机械密封频繁泄漏是困扰乙烯生产的老难题。
This series pump features a unique impeller structure and a new mechanical seal, and can effectively transfer and long fibers containing solids.
该系列泵采用独特叶轮结构和新型机械密封,能有效地输送含有固体物和长纤维。
This paper put forward the fundamental idea of design of blade mechanical seal with the structure of end assisting seal from the angle of improving the seal structure.
文章从改进密封结构的角度提出了带有端面辅助密封结构的刀口机械密封装置结构设计的基本思路。
应用推荐