Melt index (mi) is the most important parameter in determining the polypropylene's grade.
熔融指数是工业聚丙烯生产中决定聚丙烯牌号最重要的指标。
The optimal dosage of chain extender was selected to PA1010 with different melt index (MI);
针对具有不同熔体流会指数（MI）的PA材料，得出最佳的扩链剂加入量；
The melt index and ethylene content of clear PP resin for beverage bottles at home and abroad were analyzed.
剖析了国内外饮料瓶用透明聚丙烯熔体指数，乙烯含量。
With PP chips and antibacterial matrices blent, the antibacterial special raw material with high melt index is prepared for speed spinning.
采用聚丙烯切片、抗菌母粒共混，制成高熔融指数的抗菌高速纺专用料进行纺丝。
Compared with other catalysts, CSI catalyst is more suitable for producing high-melt index polypropylene in the batch bulk polymerization plant.
CS I型催化剂适用于在间歇本体聚丙烯装置上生产高熔体指数聚丙烯。
The compound inorganic particles synergistic hybridization effect was studied by comparing the melt index, mechanics capability and the morphology.
通过对复合材料熔体指数、力学性能以及形态结构的比较，探讨了无机组合粒子级复配共混的协同效应。
The results show that the grafting ratio will increase when the content of DCP and MAH increase, but the melt index will decrease in the same time.
结果表明，接枝率随着马来酸酐、引发剂用量的增加而增加，熔体流动速率随着引发剂用量的增加而减少。
The melt index (MI), heat distorsion temperature (HDT), solvent resistance, thermal stability, mechanical properties and fracture morphologies were presented.
并对其熔融指数(MI)、热变形温度(HDT)、抗溶剂性、热稳定性、力学性能和破坏形态进行了研究。
Influence of inorganic pigments on toner morpology and relations of toner composition with glass transition temperature, soften temperature and melt index were investigated.
墨粉的玻璃化转变温度、软化 点、熔融指数与墨粉组成的关系；
The influences of substrates, melt index (MI) and VAC content in EVA, selection and add-on of peeling force stabilizers on the properties of projective film products are studied.
研究了基材、EVA中熔融指数和醋酸乙烯含最、剥离力稳定剂的选择及用量对保护膜产品性能的影响。
The relationship between PP melt index and PP filament tenacity is discussed. The filaments are obtained the one-step equipment of producing high tenacity PP filament which made by FARE Co.
在意大利FARE公司卧式一步法丙纶高强丝设备上，研究了聚丙烯熔融指数与丙纶高强丝强度的关系。
The melt flow index of the blends was increased when the content of PEEK was decreased and melt temperature was increased.
结果表明：共混物的熔体流动指数随PEEK含量的降低和熔体温度的升高而增加；
The stable production of the specialty P240 for tubing with large diameter was realized under the condition of low melt flow index.
大口径管材专用树脂P240实现了低熔体流动指数下的平稳控制。
The film index is higher than that of bulk glass of the same composition as the target, but prepared by rapid quenching from the melt.
薄膜折射率高于与靶成分相同的体型玻璃折射率，而此玻璃是由熔体迅速冷却制得的。
The film index is higher than that of bulk glass of the same composition as the target, but prepared by rapid quenching from the melt.
薄膜折射率高于与靶成分相同的体型玻璃折射率，而此玻璃是由熔体迅速冷却制得的。
应用推荐