So this is the one that's showing us the mole fraction in the liquid phase.
这是告诉我们,液相摩尔分数的曲线。
So that means just reading off it, this is xB, that's the liquid mole fraction.
直接读出来，可得是xB，是液相摩尔分数。
Now, of course, since this is a mole fraction, it's always between zero and one.
现在，当然，由于这是摩尔分数，它总是处于零到一之间。
And if we go over here, this is telling us about the mole fraction in the gas phase.
如果我们到达那，它告诉了我们气相的摩尔分数。
That the vapor pressure of the solute is related to the mole fraction in the solution.
溶质的蒸汽压，和溶液中溶质的摩尔分数成正比。
The higher mole fraction of hydrophobe, the stronger viscosity enhancement effect.
且疏水单元摩尔分数越高，盐增黏效应越显著。
If you look and see, well, now we should be able to determine the mole fraction in the gas as well.
如果你看，好，现在我们也可以确定，气相中的摩尔分数。
It's not easy to calculate a priori what it's going to do all the way across the phase diagram for any mole fraction.
对于任一摩尔分数，去预计它穿越相图，会做什么并不容易。
The constraint is that the sum of all the mole factions has to be equal to one That's what it is, to be a mole fraction.
约束条件是,所有摩尔分数之和等于1。,这就是摩尔分数的意义。
x So the mole fraction at any time is n minus x divided by the total number of moles, x which we just calculated as n plus x.
任何时候的摩尔分数是n减,除以总摩尔数，就是我们计算的n加。
Now, you can draw the same diagram in, instead of pressure, mole fraction, you can draw the same diagram in terms of temperature.
现在，我们画相同的相图，但是不是压强和摩尔分数，而是温度的相图。
The highest gasification efficiency reached 109% and the mole fraction of hydrogen in product gas could be in excess of 40%.
气化率最大可以达到109%，气体产物中氢气的体积含量可以超过40%。
Average relative deviations between calculated values and experimental data of gas phase mole fraction were all less than 0.78%.
汽相摩尔分数的实验值和计算值的平均相对偏差均小于0.78%。
That means I could follow the same sort of procedure that I indicated before when we looked at the pressure mole fraction phase diagram.
这意味着我们可以用，之前压强摩尔分数，相图里类似的方法。
And the point is, now we're going to start, since the mole fraction in the gas phase that we're starting from is the same number as this was.
我们从这一点开始，因为气态的摩尔分数不变，我们从之前相同的数字开始。
Modified meta-aramid(PMIA) copolymer with TPC mole fraction of 0.05~0.15 was prepared by low-temperature-solution polycondensation in DMAc.
采用低温溶液法共缩聚反应合成了对苯二甲酰氯（TPC）摩尔分数为0.05~0.15的改性间位芳香族聚酰胺（ PMIA）共聚物。
For a given media, and at a constant total pressure and temperature, the partial pressure of oxygen is proportional to oxygen mole fraction.
对一个给定的媒介，在恒定的总压和温度下，局部压力与氧的克分子数成比例。
So in general, we don't have a simple analytical expression for what the pressure is going to do as a function of mole fraction a ll the way from zero to one.
所以通常来说，我们不会有，一个简单的解析式，描述压强，作为摩尔分数从零到一，的函数的变化形式。
And the point here is that unlike this case, where you have a linear relationship, the relationship between the pressure and the liquid mole fraction isn't linear.
关键点在于与这个情况不同，这里我们有的是一个线性的关系，压强和液相摩尔分数的关系不是线性的，我们仍然可以把它画出来。
NRTL model was used to correlate and predict the LLE data, and parameters of the model were obtained by using simplex method with objective function of mole fraction.
用单纯形优化法，选用摩尔分数目标函数求出了相应的模型参数。
The NRTL model was used to correlate and predict the LLE data of system and obtained the model's parameters by using of simplex method with the objective function of mole fraction.
用单纯形优化法，选用摩尔分数的目标函数求出了相应的模型参数。
NRTL model was used to correlate and calculate LLE data of system and model 's parameters were obtained by using of simplex optimization method with objective function of mole fraction.
用单纯形优化法，选用摩尔分数目标函数求出了相应的模型参数。
NRTL model was used to correlate and calculate LLE data of system and model 's parameters were obtained by using of simplex optimization method with objective function of mole fraction.
用单纯形优化法，选用摩尔分数目标函数求出了相应的模型参数。
应用推荐