It provides the motor power for the circulatory system.
它为循环系统提供原动力。
Power parameter include: motor power, rated speed, motor model, etc.
动力参数包括：电动机功率、额定转速、电机型号等。
If motor power or conventional match, then the motor can cause overload.
如果电机功率还是按常规来配的话，那么电机也会造成过载。
The impact of working stroke to maximum of servo motor power was also analyzed.
分析了工作行程对所需伺服电机最大功率的影响。
It can obtain the improve of power factor of the input motor power, and can lighten its capacity.
可实现电机输入电源功率因数的改善，减轻其容量。
But, if you run the motor power at around 60 you will get a relative speed of 6-10 feet per minute.
但是，如果您运行的电机功率约为60你会得到一个相对速度为每分钟6 - 10米。
Motor matched according to 1 or 1.4 power. If motor power exceed, the customer must point out in order.
按泵设计点轴功率1或1.4倍配备电机，超过匹配功率，请用户在订货时提出。
So the invention has the advantages of simple control structure, low motor power and low energy consumption.
因此，本发明具有控制结构简单，电机功率小，能耗低等优点。
The feasibility of this drive structure is analyzed, a method of calculating motor power and torque is established.
分析了该驱动方式的可行性，并建立了电机主要选型参数的计算方法。
With the speed controller on the push handle the attendant can easily control the motor power while guiding the chair.
随着对随之而来的推手柄可以方便地控制电机功率，同时指导椅子速度控制器。
Pressure spring machine is composed of main machine, control system, motor power unit, auxiliary device and auxiliary equipment.
压簧机械由主机，控制系统，电机动力单元，辅助装置，附属设备组成。
The construction, force calculation and motor power calculation are described in the article for the hold-down system in plate mills.
论述中板轧机压下装置的组成及结构、力的计算、电机功率的计算。
In this paper, principle of design and study of three-phase induction motor power measuring device is discussed in theory and practice.
本文从理论和实践方面探讨了矿用三相异步电机功率测量装置的设计及研制原理。
The article mainly introduces the theoretically calculating formula of honeycomb coal die_forming machine productivity and motor power.
介绍了冲压式蜂窝煤机的生产率和电机功率的理论计算公式。
Remark: the processing dimensions (length and width), overall dimension of equipment and motor power are subject to customers 'demands.
注：加工长宽尺寸和设备外形尺寸，电机功率，可根据客户需要制定尺寸。
The calculating formula of determining compressor structure parameter is derived by thermodynamic counter calculation based on motor power.
推导出了按电动机功率，通过热力学逆运算，确定压缩机结构参数的计算公式。
The assemble process of Conduit and Seat Ring belong to cylinder header will do an important influence on the whole motor power performance.
发动机缸盖进排气孔的导管和座圈装配质量直接影响整机动力性能。
This paper puts forword a improved method to make up the insufficiency of actual decoupling design for motor power assembly mounting system .
针对现行的发动机动力总成悬置系统解耦设计方法的不足，提出了一种针对发动机主要激振力（矩）进行解耦设计的改进方法。
In this paper, a method is proposed to determine surface dynamometer CARDS by actual motor power curves and which has been used in the field.
本文提出了利用抽油井实测功率曲线计算示功图的方法，并将其应用于实际。
Reference to research status of MDT and by analyzing the special working environment of the ESP, the multi-signal are carried with motor power line.
对空载、带载情况下变频器产生的不平衡电压和高次谐波的含量进行了测试与分析。
In addition, the design process of the wave maker control hardware is analysed in detail, and a general selection method of the motor power is proposed.
另外，详细分析了造波机控制硬件的设计过程，并在电机功率的选取上总结出一种通用方法。
The conveyor belt motor with great speed Shanghai copper motor, motor power 3KW, according to production requirements and can mediate transmission speed.
本输送带电机配备上海大速全铜电机，电机功率3KW，且可以按照生产要求调解输送速度；
The conveyor motor speed copper and Shanghai with a motor, motor power 3KW, in accordance with production requirements and can mediate transmission speed;
螺杆上料机采用电机配备上海大速全铜电机，电机功率3KW，且可以按照生产要求调解输送速度；
Optimization design of pass and computation of the main driving motor power under operation show that the rolling energy consumption may be reduced by 3.19%.
优化孔型设计与现场主电机功率值的计算表明，轧制能耗可减少3.19%。
Roller gravity conveyors move product without motor power by using a slope to convey products. Rollers have spring loaded axles for easy removal or replacement.
无需发动机推力，只需要一个倾斜的坡度就可运输产品。
The power of the selection is in meet the job pressure and volume flow conditions, power supply capacity that can satisfy matching the use of driving motor power can.
功率的选型是在满足工作压力和容积流量的条件下，供电容量能满足所匹配驱动电机的使用功率即可。
The article gives the calculation procedure of the motor power required by hot sawing machines and the design features of hot sawing machines with different structures.
介绍热锯机需要的电机功率的计算过程。对不同结构热锯机进行比较。
This article describes the principle and method of testing AC motor power by using the microcontroller(8031). The hardware and software of the system are also presented briefly.
本文介绍用8031单片机测试电机交流功率的原理及方法，并对系统的硬件和软件作了简要说明。
In order to satisfy the operation requirement of the rated thrust of the propeller, the propulsion motor performs only in rated torque on the low speed, so the motor power is low.
认为以满足螺旋桨额定推力为目的，推进电动机只需要低速输出额定转矩来实现，即输出功率较低。
In order to satisfy the operation requirement of the rated thrust of the propeller, the propulsion motor performs only in rated torque on the low speed, so the motor power is low.
认为以满足螺旋桨额定推力为目的，推进电动机只需要低速输出额定转矩来实现，即输出功率较低。
应用推荐