Parting line locks are required on all molds.
琐模块所有的模具都需要。
The injection mould parting line and its sequence as sizing space split were described.
主要阐述了注射模的分型面以及它的顺序、定距分型。
The parting line or the parting surface is line or surface that separates the cope and drag.
分型线或分型面是分离上下型箱的线或面。
The part may stick on the angle lifter, so we need to consider the parting line for this area.
产品可能粘斜顶，所以我们需要考虑粘斜顶的部分如何分型。
When you design this type of plastics mold, parting line must be designed according the Max silhouette curves.
当您设计这种类型的塑料模具，型线的设计必须根据马克斯轮廓曲线。
In this paper, a new approach to automatically searching the parting line in injection mold design is introduced.
提出了一种自动搜索模具分型线的方法。
Coining is usually done on surfaces parallel to the parting line, and little metal flow is involved in the operation.
铸币通常是做表面平行的线，与小金属流动是参与行动的。
If the parting line cannot be on a single plane, then it is good practice to use symmetry of the design to minimize the side thrust forces.
如果分模面不能在单一平面，利用设计的对称性来减小侧向推力不失为一种好方法。
Heaping on the clamp force, makes the mold harder to "breathe" or vent, and over time, can permanently hob closed the vents on the parting line.
多余的锁模力，可能让模具无法“呼吸”或排气，周期超时等，对模具分模线的挤压。
According to the parting direction and the description of boundary, the parting line of a body is decided and then the parting surface is designed.
根据开模方向，结合零件的边界描述确定零件上的分模线，进而对分模面进行设计。
Using the stripper plate pushes out the die-frame in the die, after opening the die, the push-bar pushes out the stripper plate along the parting line;
该模具用卸料板推出机构的模架，开模后，推杆将卸料板沿分型面推开；
Undercuts and similar parting line issues are made highly visible two dimensionally on our computer monitors-allowing us to avoid costly and time-consuming errors.
削弱和类似临别线的问题是非常明显的两个三维电脑显示器我们，使我们能够避免昂贵和费时的错误。
Mold Flow Analysis, Temperature Analysis, Fill Analysis, Pressure Analysis, Buckling Deformation Analysis, Structure Review, Parting Line, Fixed Mold, Moving Mold, Water Circuit.
模流分析、温度分析、填充分析、压力分析、翘曲变形分析、结构评审（初审、定型评审、终审）、分型线结构评审、定模结构评审、动模结构评审、水路分布评审。
It is important to note the the edge of the parting tool was to brought to the line on the low side.
这是很重要的要注意边缘的临别的工具，是为了使该线偏低。
A new style automobile with the line main body-fuse box mold is introduced, state the mold structure, parting surface design, product ejection design and so on. practical mold structure is concluded.
介绍一新款汽车用线路主体——熔断器盒的模具，对其模具结构、分型面的设计、产品顶出设计等进行了阐述，给出实用可行的模具结构形式和设计方法。
Resin sand mould was adopted with precoated sand core. The upper and bottom half boxes used horizontal pouring design with box middle line as parting face.
采用树脂砂砂型、覆膜砂砂芯，上、下两个箱体均采用平做平浇的工艺方案，并选取箱体中线为分型面。
Resin sand mould was adopted with precoated sand core. The upper and bottom half boxes used horizontal pouring design with box middle line as parting face.
采用树脂砂砂型、覆膜砂砂芯，上、下两个箱体均采用平做平浇的工艺方案，并选取箱体中线为分型面。
应用推荐