The pinion shaft runs in porous bronze bearing bushes.
小齿轮轴运行多孔青铜轴承衬套。
The differential pinions also turn with the pinion shaft.
行星齿轮也和行星齿轮轴旋转。
Remove the universal joint strap bolts at the pinion shaft yoke.
在小齿轮轴轴轭处拆卸万向节扣夹螺栓。
Power will go from the pinion shaft through the differential pinions to only one side gear because the other side gear is stationary.
来自行星齿轮轴的功率通过行星齿轮，只到达一个半轴齿轮，而另一个半轴齿轮保持静止。
Seal air is injected into the labyrinth seals located at the main motor shaft (top and bottom) and at the pinion shaft driving the motor.
密封空气被注入到主马达轴（顶部和下部）和驱动马达的齿轮轴的迷宫式密封里。
The situation for pinion shaft broken of increasing gear for nitrogen oxide centrifugal compressor is described. The trouble reason is analyzed.
叙述了氧化氮离心压缩机增速机小齿轮轴扭断的状况，分析了产生事故的原因。
If the rack is fixed and the pinion is carried in Bearings on a table guided on tracks parallel to the rack, rotation of the pinion shaft will move the table parallel to the rack.
如果齿条固定，小齿轮装在工作台的轴承上，而工作台所在的导轨与齿条平行，那么小齿轮的轴转动时，就会带动工作台平行齿条而移动。
Power flows through the drive pinion, ring gear, case, and pinion shaft to the differential pinions. Then power splits equally and goes to the side gears, axle shafts, and drive wheels.
功率经过主动齿轮、从动锥齿轮、壳体和行星齿轮轴来到行星齿轮，然后功率被均分，送到半轴齿轮、半轴，最后到达驱动轮。
The starter motor is a simple direct current (DC) motor which has a pinion gear attached to its shaft.
启动电机是一个简单的直流电机，在它的轴上有一个小齿轮。
Change of Cycloid pinwheel planetary reducer output shaft and pinion parameters on their way to extend the life of Cycloid pinwheel planetary reducer.
改变摆线针轮行星减速机输出轴和其上小齿轮参数的方法来延长摆线针轮行星减速机的使用寿命。
The driving power enters the differential through the drive pinion on the end of the propeller shaft.
也就是说，驱动力是从传动轴末端的传动齿轮输送到差速器的。
The pinion gear is attached to the steering shaft.
该齿轮连接转向轴。
The hypoid gear is in common use today due mainly to the fact that the offset pinion allows the propeller shaft to be set below, (for cars) or above, (for commercial vehicles) the crown wheel center.
现在的主减速器普遍使用准双曲面圆锥齿轮，这主要是因为 主动锥齿轮的偏移允许轿车上传动轴布置得比从动锥齿轮低 一些，而商用车上又允许布置得比从动锥齿轮高一些。
Alternatively, the R11 shaft accepts pinions or pulleys for use in rack and pinion or cable measuring systems.
另外，到r11在接受轴齿轮齿条式或电缆使用齿轮或滑轮测量。
Alternatively, the R11 shaft accepts pinions or pulleys for use in rack and pinion or cable measuring systems.
另外，到r11在接受轴齿轮齿条式或电缆使用齿轮或滑轮测量。
应用推荐