Because there are different ways to build a gear reduction unit, eg chain and sprocket or gearbox, we are only showing you the setup Angle of the muller.
由于有不同的方法来建立一个齿轮减速装置，如链及链轮或变速箱，我们只显示您的马勒设置的角度。
Electric motors in other countries may operate at 1350 RPM so a different reduction gear set will be required.
在其他国家电动机可运行在1350转这样一个不同的减速将需要设置。
An automatic is a device that provides gear reduction, with resulting multiplication of torque.
自动变速器是一个提供减速、同时增加扭矩的装置。
With a gear reduction, the output speed can be reduced while the torque is increased.
如果使用齿轮减速，就可以降低输出速度，同时增加力矩。
The damage cause of reduction gear of cooling tower fan is analyzed, some countermeasures are adopted.
分析凉水塔风机减速箱齿轮损坏的主要原因，采取相应的防范措施。
Through the analysis of material and construction, the dissimilar steel gear is successfully welded using stress reduction zone by heating and proper assemble and welding sequence.
通过对铸焊齿轮的材料和结构的分析，利用“加热减应区”法及适当的装配焊接顺序，成功地焊接了异种金属的合金钢齿轮。
Vertically mounted engine driving main rotor via toothed belt as second-stage reduction gear.
垂直安装的引擎，该引擎作为第二阶段的减速齿轮齿形带主旋翼。
The V belt wheels of noise experimental table of main carriage reduction gear must suit drive ratio, be lightest in weight and least in moment of inertia .
为降低轿车主减速器噪声测试试验台本底噪声，其传动系统采用了四对三角胶带传动。
The status of various reduction motors of pumping unit has been analyzed, and a research on design of a kind of three groups duplicate gear reduction motor has been made.
分析抽油机上使用的各种减速电机的现状，对抽油机的三组双联齿轮减速电动机设计进行了研究。
The distortion of gears and gear shafts resulting from carburizing and quenching is difficult to avoid in production, and the reduction in distortion is a difficult problem in technique.
在生产中，齿轮和齿轮轴的渗碳和淬火畸变是难以避免的，减小其畸变量是一个技术难题。
By the use of a finite element method the authors have calculated the stress and rigidity of a main reduction gear box case body for a certain type of cement mill.
应用有限元法对某型水泥磨机主减速齿轮箱箱体的应力和刚度进行了计算。
DD652 or EQ153 Pressed and welded steel banjo housing, single reduction, hypoid gear.
DD652或EQ 153冲压焊接钢管班卓琴住房，单减少，双曲面齿轮。
The primary drive gear(crankshaft gear)and the primary driven gear are the source of noise due to their high speed and bigger reduction ratio.
作为摩托车初级传动的曲轴齿轮及初级从动齿轮，由于转速高及降速比大，是产生噪声的主要因素。
Based on many years experience for design, discusses the factors which affect the noise of gear box, controls and noise reduction methods.
根据多年从事齿轮箱设计工作的经验，论述影响齿轮箱噪声的因素以及控制与降低噪声的方法。
Finally, taking SS8 electric locomotive driving gears for example, the simulation results are analyzed, and the specific measures about the reduction of gear wear are proposed as well.
最后以ss8型电力机车传动齿轮为例，分析了仿真结果，并提出减少机车传动齿轮磨损的具体措施。
An epicyclic reduction gear with reasonable reliability and compact configuration is described in this paper.
本文介绍了一种具有可靠度合理，且结构紧凑的行星减速器。
The single stage skewed tooth cylindrical gears reduction gear optimized design, is a multi-objective optimization question.
单级斜齿圆柱齿轮减速器的优化设计，是一个多目标优化问题。
In a gear reduction unit, for example, the shaft diameters are usually set by the requirement of getting sufficient shaft stiffness to keep the misalignment of the gear teeth within strict bounds.
例如，在齿轮减速装置中，轴径通常是由轴的刚度要求决定以在严格界限内保持齿轮齿形的不错位。
Pressed and welded steel banjo housing, single reduction, hypoid gear, ratio 6.33:1.
冲压，焊接钢班卓琴住房，单减少，双曲面齿轮，比6.33：1。
Abnormal noise often occurs in motor vehicle transmission system especially in propeller shaft and final reduction gear.
汽车传动系特别是传动轴与主减速器常产生异常响声。
The result of static calculation showed that the tooth profile long modification of spur bevel gear possesses better effects of vibration reduction.
静态计算结果表明，直齿锥齿轮齿廓长修形具有较好的减振效果。
Foot mounting brackets are available also, when the pump must be run slower than direct-drive speeds allow, with belt or gear-reduction assembly.
当泵的运行速度慢于直接驱动速度时，底座安装支架也是可以的，带有传送带或减速齿轮部件。
The reduction gear drive mechanisms are substantially sealed and disposed inside the corresponding side plates.
减速齿轮传动机构基本上被密封，并且设置在相应的侧板内侧。
Gears do several important jobs, but most important, they provide a gear reduction in motorized equipment.
齿轮有很多作用，但最重要的作用是动力设备的减速。
The invention relates to a reduction gearbox of an electric tool, in particular to an assembling structure of double-speed impact electric drill gear reduction gearbox.
本发明涉及一种电动工具的减速箱，具体地说是一种双速冲击电钻齿轮减 速箱的装配结构。
The movement is reliable USES the reduction gear joint belt pulley and the sprocket feed and disposes the transmission to rise the tight organization the guarantee running rate.
运行可靠，采用减速器联接皮带轮及链轮传动，并配置传动涨紧机构，保证运行速度。
The electric motor through the reduction gear, leads the reel rotation, causes the steel wire to wind the reel or to lay down from the reel, rises and falls the heavy item.
电动机通过减速器，带动卷筒转动，使钢丝绳绕上卷筒或从卷筒放下，以升降重物。
The whole finite element model includes 5 nodes and 5 elements, and these element types are D. C. motor element, reduction gear element, beam element, crank element and buffer element.
有限元模型包括5个节点和5个单元，这些单元分别是直流电机单元、齿轮减速器单元、梁单元、曲柄单元和缓冲器单元。
The whole finite element model includes 5 nodes and 5 elements, and these element types are D. C. motor element, reduction gear element, beam element, crank element and buffer element.
有限元模型包括5个节点和5个单元，这些单元分别是直流电机单元、齿轮减速器单元、梁单元、曲柄单元和缓冲器单元。
应用推荐